Difference between revisions of "Zero2/Hardware/Revisions"

Latest revision as of 03:43, 7 July 2022

 Radxa Zero 2 >  Hardware >  Hardware revisions

Version	Comment
1.0	Initial version Known issues: Lack of clearance around microSD card slot resulting the card will be blocked for insertion. (Workaround: lift the card corner slightly during insertion, so the card can "sit" on that blocking component when fully inserted) TYPE-C headers are slightly misaligned. PCB mounting hole location is different from Zero, as such a proposed universal case cannot share holes on the USB connector side. USB 3 port may not be recognized by the board. (Manually fixed on sample boards) ~~GPIO pin 16 and 24 are connected on the same bus. 16 will be replaced by SARADC_CH1.~~ ~~GPIO pin 36 is an open drain pin. Works fine for input but need pull up for output.~~ ~~Fan's PWM generator is occupied by VDDCPU_B. Preferably an unused PWM pin should go there. Otherwise `gpio-fan` will be used in device tree.~~ Green LED might be too bright
1.1	Major changes: Fix microSD card clearance. Pin 16 is now connected to GPIOZ_8. Pin 22 is now connected to GPIOZ_9. Pin 36 is now pulled up. Fan is now connected to GPIOAO_11 (PWMAO_A). Relocated fan header, and switched to a smaller CSI connector. Update CSI, DSI pin definition. Switch wireless module from AP6256 to AW-CM256SM, which requires different firmware. Distro developers are recommended to include firmwares for both modules.
1.2	Major changes: Add I2S data pin on pin 31 and 36

@@ Line 12: / Line 12: @@
 | 1.0
 | Initial version
-* lack of clearance around microSD card slot resulting the card will be blocked for insertion. (Workaround: lift the card corner slightly during insertion, so the card can "sit" on that blocking component when fully inserted)
+Known issues:
-* TYPC-C headers are slightly misaligned.
+* <del>Lack of clearance around microSD card slot resulting the card will be blocked for insertion. (Workaround: lift the card corner slightly during insertion, so the card can "sit" on that blocking component when fully inserted)</del>
+* TYPE-C headers are slightly misaligned.
 * PCB mounting hole location is different from Zero, as such a proposed universal case cannot share holes on the USB connector side.
 * USB 3 port may not be recognized by the board. (Manually fixed on sample boards)
-* GPIO pin 16 and 24 are connected on the same bus. 16 will be replaced by SARADC_CH1.
+* <del>GPIO pin 16 and 24 are connected on the same bus. 16 will be replaced by SARADC_CH1.</del>
-* GPIO pin 36 is an open drain pin. Works fine for input but need pull up for output.
+* <del>GPIO pin 36 is an open drain pin. Works fine for input but need pull up for output.</del>
-* Fan's PWM generator is occupied by VDDCPU_B. Preferably an unused PWM pin should go there. Otherwise <code>gpio-fan</code> will be used in device tree.
+* <del>Fan's PWM generator is occupied by VDDCPU_B. Preferably an unused PWM pin should go there. Otherwise <code>gpio-fan</code> will be used in device tree.</del>
+* Green LED might be too bright
 |-
 | 1.1
-| Pending
+| Major changes:
+* Fix microSD card clearance.
+* Pin 16 is now connected to GPIOZ_8.
+* Pin 22 is now connected to GPIOZ_9.
+* Pin 36 is now pulled up.
+* Fan is now connected to GPIOAO_11 (PWMAO_A).
+* Relocated fan header, and switched to a smaller CSI connector.
+* Update CSI, DSI pin definition.
+* <b>Switch wireless module from AP6256 to AW-CM256SM</b>, which requires different firmware. Distro developers are recommended to include firmwares for both modules.
+|-
+| 1.2
+| Major changes:
+* Add I2S data pin on pin 31 and 36
 |}