Please enable javascript, or click here to visit my ecommerce web site powered by Shopify.
Jump to: navigation, search

Rock3/hardware/3a

< Rock3‎ | hardware
Revision as of 13:00, 3 December 2021 by Stephen (Talk | contribs)


    ROCK 3 >  Hardware >  ROCK 3 Model A Main Board

ROCK 3 Model A Main Board

This hardware user manual provides information about the features and signals available on ROCK 3 A board.

Rock-3-a-with-label.jpg

1.Power Button

The power button is used to turn the device on and off.

Short pressing power button would power on/off the device. This is what we called power on/off via software.

Power button also provides function of hardware power on/off the device.

When the system is crashed, you can shutdown the device via this method. Press and hold the power button for at least 6 seconds. Then release the power button. After that short press power button would power on the device.

2.3-pin Recovery Header

This is the 3-pin definition table.

Pin# Name
1 FSPI_CLK
2 GND
3 RECOVERY
About FSPI_CLK pin

Short-circuit the Shor FSPI_CLK pin and GND pin to make SPI Nor flash unavailable.

Please note that you should short-circuit pin#1 and pin#2 always when spi nor flash is not used. Like the yellow left hat.

3a-maskrom.png

About Recovery pin

Shor-circuit Recovery pin and GND pin to boot device into loader mode.

Below is the steps of booting device into loader mode.

  • Make sure that there is system image (Linux/Android) on board.
  • Short pin#2 and pin#3
  • Plug in the Type-C adapter
  • Wait for about 3 seconds
  • Remove wire between pin#2 and pin#3

3.MIPI Display Interface

The ROCK Pi 4 Model A and B are equipped with one HDMI connector and one MIPI DSI. As for HDMI, the maximum resolution is 4k@60Hz. Any HDMI monitor should work as a display for the Pi 4. As for MIPI DSI, it is designed for raw LCD pannel. HDMI and MIPI DSI can work at the same time.

The MIPI DSI interface pin specification shows below.

Pin# Name
1 VCC_MIPI
2 VCC_MIPI
3 GND
4 I2C_SDA_AUDIO
5 I2C_SCL_AUDIO
6 GND
7 MIPI_TX/RX_D0P
8 MIPI_TX_RX_D0N
9 GND
10 MIPI_TX/RX_CLKP
11 MIPI_TX_RX_CLKN
12 GND
13 MIPI_TX/RX_D1P
14 MIPI_TX/RX_D1N
15 GND

4.M.2 E Key

M.2 E Key pin signal definition table.

Pin# Name
1 GND
2 VCC3V3_WF
3 USB2_M2_DP
4 VCC3V3_WF
5 USB2_M2_DM
6 WIFI_LED
7 GND
8 PCM_CLK/I2S_SCK
9 SDIO_CLK
10 PCM_SYNC/I2S_WS
11 SDMMC2_CMD_M0
12 PCM_OUT/I2S SD_OUT
13 SDMMC2_D0_M0
14 PCM_IN/I2S SD_IN
15 SDMMC2_D1_M0
16 NC
17 SDMMC2_D2_M0
18 GND
19 SDMMC2_D3_M0
20 BT_WAKE_HOST_H_GPIO4_B4
21 WIFI_WAKE_HOST_H_GPIO3_D5
22 UART1_RX_M0
23 WIFI_REG_ON_H_GPIO3_D4
32 UART1_TX_M0
33 GND
34 UART1_CTS_M0
35 PCIE_TXP
36 UART1_RTS_M0
37 PCIE_TXN
38 NC
39 GND
40 NC
41 PCIE20_RXP
42 BT_REG_NO
43 PCIE20_RXN
44 NC
45 GND
46 NC
47 PCIE20_REFCLKP
48 NC
49 PCIE20_REFCLKN
50 WIFIBT_32KIN_1T1R
51 GND
52 PCIE_PERSTN
53 PCIE_CLKREQN
54 HOST_WAKE_BT_H
55 PCIE_WAKEN
56 BT_REG_ON_H
57 GND
58 I2C4_SDA_M1
59 NC
60 I2C4_SCL_M1
61 NC
62 NC
63 GND
64 NC
65 NC
66 NC
67 NC
68 NC
69 GND
70 BT_WAKE
71 NC
72 VCC3V3_WF
73 NC
74 VCC3V3_WF
75 GND
76 GND
77 GND
78 NC
79 NC

5.Power LED

6.User LED

7.Power Supply

The ROCK 3A is powered by Type-C port and has a wide range of input voltage, from 9V to 21V. The ROCK 3A supports USB Type-C PD 2.0 with 9V/2A, 12V/2A, 15V/2A and 20V/2A. Besides, the Pi supports QC 3.0/2.0 with 9V/2A and 12V/1.5A. The Type-C cable you using needs to support data communication. We call it USB Type-C charging data cable.

9.HDMI

The ROCK 3A is equipped with one HDMI connector and one MIPI DSI. As for HDMI, the maximum resolution is 4k@60Hz. Any HDMI monitor should work as a display for the ROCK 3A. As for MIPI DSI, it is designed for raw LCD pannel. HDMI and MIPI DSI can work at the same time.

HDMI port supports Consumer Electronics Control (CEC) function. Using ROCK 3A connected to a TV that supports CEC, you can use the command line cec-client application to control the inputs and the TV itself.

The HDMI interface pin specification shows below.

Pin# Name
1 HDMI_TX2P
2 GND
3 HDMI_TX2N
4 HDMI_TX1P
5 GND
6 HDMI_TX1N
7 HDMI_TX0P
8 GND
9 HDMI_TX0N
10 HDMI_TXCP
11 GND
12 HDMI_TXCN
13 HDMI_CEC
14 NC
15 DDC_SCL
16 DDC_SDA
17 GND
18 VCC5V0_HDMI
19 PORT_HPD

10.MIPI Camera Interface

There is a wide range of camera applications in our lives. MIPI CSI 2 lane on board support 800 MP camera via FPC connector.

The MIPI CSI interface pin specification shows below.

Pin# Name
1 VCC_CAM
2 I2C4_SDA
3 I2C4_SCL
4 CAM_MCLK
5 CAM_GPIO1
6 GND
7 MIPI_RX0_CLKP
8 MIPI_RX0_CLKN
9 GND
10 MIPI_RX0_D1P
11 MIPI_RX0_D1N
12 GND
13 MIPI_RX0_D0P
14 MIPI_RX0_D0P
15 GND

11.Audio: 3.5mm jack with MIC

Audio can be played through speaker or headphones using a standard 3.5mm jack with MIC.

Note that HD codec supports up to 24-bit/96KHz audio.

12.PWM Fan

Rock-3a-pwm-fan-connector.png

Definition table (From top to bottom in the picture)

Pin# Name
1 +5.0V
2 PWM
3 GND

13.1000M Ethernent

14/15/21.USB

One Type-A USB 3.0 port with OTG switch, the upper one on USB 3.0 port

When the USB OTG Switch is switched to the host side, the Type-A USB 3.0 port also enables the attachment of peripherals such U Disk, keyboards, mice, USB dongle etc.

This USB 3.0 port supports On-The-Go(OTG) when the USB OTG Switch is switched to the device side. Thus the Soc is recognized as an device.

Take adb as an example. You can use a Type-A to Type-A cable as a bridge between you PC and ROCK 3A Board. In addition to the system configuration, you can setup the adb tool on your PC to access ROCK 3A over adb.

One Type-A USB 3.0 host port

Tthe Type-A USB 3.0 port enables the attachment of peripherals such U Disk, keyboards, mice, USB dongle etc.

Two Type-A USB 2.0 host port

These two ports enables the attachment of peripherals such U Disk, keyboards, mice, USB dongle etc.

One USB 2.0 signal on 40-pin header

According to the ROCK 3A SKU table, there are two USB 2.0 signal lines on 40-pin header, PIN 27&28.

When you want to select this USB function, you need to modify the hardware like this.

  • Remove R90526 R90527
  • Add R90536 R90537

16.PoE

17.SoC

SoC is RK3568.

20.General purpose input-output (GPIO) connector

ROCK 3A has one 40-pin expansion header. Each pin is distinguished by color.

For more details, see the ROCK 3A GPIO page.

Please note that do not touch the metal pins directly with your hands.

22.RTC

The RTC connector is designed according to the standard connector type.

You can distinguish '+3.3V' and '-' from the silk screen on the board.

Pin# Name
1 GND
2 +3.3V

23.PCIE M.2 NGFF M-KEY SOCKET Interface

On ROCK 3A board, M.2 connector supports up to 2T M2 NVME SSD.

The PCIE M.2 interface pin specification shows below.

Name Pin# Pin# Name
GND 1 2 +3.3V
GND 3 4 +3.3V
PERn3 5 6 NC
PERp3 7 8 NC
GND 9 10 DAS/DSS#
PETn3 11 12 +3.3V
PETp3 13 14 +3.3V
GND 15 16 +3.3V
PERn2 17 18 +3.3V
PERp2 19 20 EMMC_CMD
GND 21 22 NC
PETn2 23 24 NC
PETp2 25 26 NC
GND 27 28 NC
PERn1 29 30 NC
PERp1 31 32 NC
GND 33 34 NC
PETn1 35 36 NC
PETp1 37 38 DEVSLP
GND 39 40 NC
PERn0/SATA-B+ 41 42 NC
PERp0/SATA-B- 43 44 NC
GND 45 46 NC
PETn0/SATA-A- 47 48 NC
PETp0/SATA-A+ 49 50 PERST#
GND 51 52 CLKREQ#
REFCLKN 53 54 PEWake#
REFCLKP 55 56 NC
GND 57 58 NC
NC 67 68 SUSCLK
PEDET 69 70 +3.3V
GND 71 72 +3.3V
GND 73 74 +3.3V
GND 75

24.TF Card Interface

The TF card can be used as a system storage or an external storage. When it's used as a system storage, you had better choose the ones with storage space larger than 8GB. When it's used as an external storage, you can choose the ones with storage space up to 128GB. When the TF card is inserted into the TF card slot , the device will be automatically recognized by the system.

The TF card interface pin specification shows below.

Pin# Name
1 SDMMC0_D2
2 SDMMC0_D3
3 SDMMC0_CMD
4 VCC3V3_SYS
5 SDMMC0_CLK
6 GND
7 SDMMC0_D0
8 SDMMC0_D1
9 SDMMC0_DET_L
10 GND
11 GND
12 GND
13 GND

26. eMMC

Socket on Board Interface Feature

The high performance eMMC module is the best choice as the system storage for ROCK 3A. The eMMC module with 8GB/16GB/32GB/64GB/128GB is available.

The eMMC Socket pin specification shows below.

Name Pin# Pin# Name
GND 1 34 GND
EMMC_D5 2 33 EMMC_D6
GND 3 32 GND
EMMC_D4 4 31 EMMC_D7
GND 5 30 GND
EMMC_D0 6 29 EMMC_D1
GND 7 28 GND
EMMC_CLK 8 27 EMMC_D2
GND 9 26 GND
EMMC_D3 10 25 EMMC_CMD
GND 11 24 GND
EMMC_RSTN 12 23 VCC3V3_SYS
GND 13 22 VCC3V3_SYS
GND 14 21 VCC_1V8
EMMC_RCLK 15 20 VCC_1V8
GND 16 19 GND
GND 17 18 GND