Difference between revisions of "Rock3/dev"
< Rock3
| (12 intermediate revisions by 4 users not shown) | |||
| Line 12: | Line 12: | ||
* [[radxa-configuration | Radxa Configuration]] | * [[radxa-configuration | Radxa Configuration]] | ||
* [[Device-tree-overlays | Device Tree Overlays]] | * [[Device-tree-overlays | Device Tree Overlays]] | ||
| + | |||
------ | ------ | ||
| Line 23: | Line 24: | ||
* [[rock3/dev/install-coral-pcie-driver-and edge tpu-runtime-packages | Using Coral Edge TPU]] | * [[rock3/dev/install-coral-pcie-driver-and edge tpu-runtime-packages | Using Coral Edge TPU]] | ||
* [[rock3/dev/npu-run-test | NPU Run Test]] | * [[rock3/dev/npu-run-test | NPU Run Test]] | ||
| + | * [[rock3/dev/rknn-toolkit-with-pc | RKNN Toolkit with PC]] | ||
* [[rock3/dev/libmraa | Install libmraa]] | * [[rock3/dev/libmraa | Install libmraa]] | ||
| + | * [[rock3/dev/libmraa-cm3-io | libmraa on Radxa CM3 IO]] | ||
* [[rock3/install/spi | SPI]] + [[rock3/install/nvme | NVME SSD]] boot | * [[rock3/install/spi | SPI]] + [[rock3/install/nvme | NVME SSD]] boot | ||
* [[rock3/dev/change-kernel-params | Change kernel params ]] | * [[rock3/dev/change-kernel-params | Change kernel params ]] | ||
| Line 30: | Line 33: | ||
* [[rock3/dev/sata-on-radxa-cm3-io | Use SATA SSD on Radxa CM3 IO]] | * [[rock3/dev/sata-on-radxa-cm3-io | Use SATA SSD on Radxa CM3 IO]] | ||
* [[rock3/dev/install-docker-engineer-on-docker | Install Docker Engine on Debian]] | * [[rock3/dev/install-docker-engineer-on-docker | Install Docker Engine on Debian]] | ||
| − | + | * [[rock3/dev/usb-device-network | USB Device Network]] | |
| + | * [[rock3/dev/ap-mode-on-radxa-e25 | AP mode on Radxa E25]] | ||
| + | * [[rock3/dev/radxa-e25-ums | Radxa E25 as USB Mass Storage]] | ||
| + | * [[rock3/dev/radxa-e23-audio | Radxa E23 Audio Test]] | ||
| + | * [[rock3/dev/radxa-cm3-io-display | Use Radxa Display 10HD on Radxa CM3 IO]] | ||
| + | * [[rock3/dev/uart | Use the debug serial port as a normal serial port]] | ||
| + | * [[rock3/dev/usb-gadget | USB Gadget Support]] | ||
| + | * [[rock3/dev/qt | porting qt to rockchip platforms]] | ||
| + | * [[rock3/dev/qt_and_libwiringX | Embed wiringX into the qt project]] | ||
------ | ------ | ||
Latest revision as of 09:24, 5 June 2023
ROCK 3 > Development Guide
This page describes development tips for ROCK 3.
- How to use Radxa Official Debian
- How to use Radxa Official Ubuntu
- Radxa APT
- Radxa Configuration
- Device Tree Overlays
- debos-radxa build Radxa official system images
- Build Debian from scratch
- Using Serial Console
- PXE Boot
- Using Android Debug Bridge
- Using CAN bus communication
- Using Coral Edge TPU
- NPU Run Test
- RKNN Toolkit with PC
- Install libmraa
- libmraa on Radxa CM3 IO
- SPI + NVME SSD boot
- Change kernel params
- Mainline Development
- Unified Extensible Firmware Interface
- Use SATA SSD on Radxa CM3 IO
- Install Docker Engine on Debian
- USB Device Network
- AP mode on Radxa E25
- Radxa E25 as USB Mass Storage
- Radxa E23 Audio Test
- Use Radxa Display 10HD on Radxa CM3 IO
- Use the debug serial port as a normal serial port
- USB Gadget Support
- porting qt to rockchip platforms
- Embed wiringX into the qt project