Rockpi4/hardware/devtree overlays linux5.10
ROCK Pi 4 > Hardware > Linux5.10 Device Tree Overlays
Contents
Device Tree Overlays
Introduction
This directory contains Device Tree overlays. Device Tree makes it possible to support many hardware configurations with a single kernel and without the need to explicitly load or blacklisr kernel modules.
On Radxa borad which uses linux5.10 kernel, you can use "rsetup" to load overlays that you want to enable, rsetup load overlays' dtbo from [Radxa/overlay]
How to enable a overlay dtbo
run "rsetup" command as below:
radxa@rock-4c-plus:~$ rsetup
Please select an option below:
System Maintaince
Onboard Hardware
Overlay Management
Connectivity
User Settings
Localization
Common Tasks
About
<Ok> <Cancel>
Select "Overlay Management"
Configure Device Tree Overlay
Install overlay from source
Manage installed overlay
Rebuild boot configuration
Reset overlay libraries with kernel's default
<Ok> <Cancel>
Select "Manage installed overlay",
[ ] audioinjector-isolated-soundcard.dtbo
[ ] cm3-sodimm-io-sata.dtbo
[ ] radxa-5inch-touchscreen-on-cm3-sodimm-io.dtbo
[ ] radxa-5inch-touchscreen-on-rock-3a.dtbo
[ ] radxa-5inch-touchscreen-on-rock-3b.dtbo
[ ] radxa-cm3-io-dual-cameras-gc2053.dtbo
[ ] radxa-cm3-io-hd101boe9365-display.dtbo
[ ] radxa-cm3-io-headphone.dtbo
[ ] radxa-cm3-io-i2c0-hym8563.dtbo
[ ] radxa-cm3-io-pcie2x1.dtbo
[ ] radxa-cm3-io-radxa-10p1inch-display.dtbo
[ ] radxa-cm3-io-sata1.dtbo
[ ] radxa-cm3-io-sata2.dtbo
[ ] radxa-cm3-io-sharp-lq133t1jw01-without-hdmi.dtbo
[ ] radxa-cm3-raspcm4io-pcie2x1.dtbo
[ ] radxa-cm3-sodimm-io-raspberrypi-7inch-touchscreen.dtbo
[ ] radxa-cm3i-gmac1.dtbo
[ ] rk3399-dwc3-0-host.dtbo
[ ] rk3399-dwc3-0-otg.dtbo
[ ] rk3399-dwc3-0-peripheral.dtbo
[ ] rk3399-opp-1800.dtbo
[ ] rk3399-opp-2000.dtbo
[ ] rk3399-opp-2200.dtbo
[ ] rk3399-opp-2400.dtbo
[ ] rk3399-spi-5-enc28j60.dtbo
[ ] rk3399-spi-gpio-enc28j60.dtbo
[ ] rk3399-uart0.dtbo
[ ] rk3568-can1-m0.dtbo
[ ] rk3568-can1-m1.dtbo
[ ] rk3568-disable-gmac1.dtbo
[ ] rk3568-disable-npu.dtbo
[ ] rk3568-fiq-debugger-uart0.dtbo
[ ] rk3568-fiq-debugger-uart2m0.dtbo
[ ] rk3568-fiq-debugger-uart3m0.dtbo
[ ] rk3568-fiq-debugger-uart5m1.dtbo
[ ] rk3568-fiq-debugger-uart7m1.dtbo
[ ] rk3568-fiq-debugger-uart8m1.dtbo
[ ] rk3568-fiq-debugger-uart9m1.dtbo
[ ] rk3568-i2c2-m0.dtbo
<Ok> <Cancel>
Select the overlays you want to load with the space bar,
[*] rk3399-uart0.dtbo
Overlay with a "*" indicates that it is enabled.
How to use a overylay written by yourselt
Because of the number of products we have, writing the device tree overlay(dtbo) for each product has become a significant burden. To improve code reuse, you now need to specify metadata for dtbo to facilitate sharing of the same dtbo across different products