Difference between revisions of "Rock3/installusb-install-radxa-cm3-io"

Latest revision as of 02:39, 28 September 2022

English

    ROCK 3 >  Installation >   Install Image to eMMC from USB port (Radxa CM3 IO)

@@ Line 1: / Line 1: @@
 {{rock3_header}}
-{{Languages|rock3/install/microSD}}
+{{Languages|rock3/installusb-install-radxa-cm3-io}}
-     [[rock3 | ROCK 3]] > [[rock3/install | Installation]] >  [[rock3/install/usb-install | Install to eMMC from USB port (Radxa CM3 IO )]]
+     [[rock3 | ROCK 3]] > [[rock3/install | Installation]] >  [[rock3/installusb-install-radxa-cm3-io | Install Image to eMMC from USB port (Radxa CM3 IO) ]]
-=== Install on eMMC from USB port ===
+=== Install Image to eMMC from USB port (Radxa CM3 IO) ===
 Radxa CM3 IO supports Maskrom mode, which is a special operation mode for CPU to wait for USB OTG port command.
-The PC tools we use to communicate with Radxa cm3 io in Maskrom mode are the '''rkdeveloptool''' and '''RKDevTool'''.
+The PC tools we use to communicate with Radxa cm3 io in Maskrom mode are the '''rkdeveloptool on linux/macOS PC''' and '''RKDevTool on Windows PC'''.
-We use '''the rkdeveloptool in Linux/macOS '''
 === Requirement ===
 * Radxa CM3 IO (with Radxa CM3 )
-* Power adapter
+* DC 12V power adapter
-* USB Male A to Micro usb cable.
+* USB Male A to Micro USB cable
+* [[Rock3/downloads | Radxa CM3 IO system image]]
+* RK356X loader: [https://dl.radxa.com/rock3/images/loader/rock-3a/rk356x_spl_loader_ddr1056_v1.10.111.bin rk356x_spl_loader_ddr1056_v1.10.111.bin]
 === Install Tools&Drivers ===
 Please check this guide, [[rock3/install/rockchip-flash-tools | Install rockchip flash tools under Windows/Linux/MacOS PC]].
-=== Boot the board to maskrom mode ===
+=== Boot the Board to Maskrom Mode ===
 To boot Radxa CM3 IO  into maskrom mode is simple:
 * Power off the board
-* remove microSD card
+* Remove microSD card
-* Plug the USB Male A to Micro USB cable to Radxa CM3 IO  OTG port(see graphic below), the other side to PC
+* Plug the USB Male A to Micro USB cable to Radxa CM3 IO OTG port(see the following picture), the other side to PC
 [[File:Cm3 io micro usb.jpeg | 400px]]
-* Press and hold the golden button (see graphic below).
+* Press and hold the golden button (see the following picture)
 [[File:Cm3-io-key.jpeg | 400px]]
-* Power on the board
+* Plug in DC 12V power adapter
-* See usb device
+* Check usb device
 ** For Linux/macOS: lsusb result: '''Bus 001 Device 112: ID 2207:350a Fuzhou Rockchip Electronics Company'''
 Alternatively, if you are running Android and can access ADB, you can reboot the device to loader mode 'adb reboot bootloader' then use the rkdeveloptool to reset the device into maskrom mode 'rkdeveloptool rd 3' or Windows RKDevTool '''Switch''' button to go to maskrom mode.
-=== Begin Installation USB -> eMMC ===
+=== Flash Images to eMMC on Board ===
-==== Linux/macOS ====
+'''Unlike balenaEtcher, rkdevtool does not support decompression of the image file, so you will have to decompress it into an img file first before flashing.'''
-On your PC, run the rkdeveloptool
+Failure to perform this step will result in non-working eMMC installation. However, the device is not bricked. You can either restart the flashing process to write the correct system image, or use micro SD card to boot.
+==== On Linux/macOS PC ====
+Make sure that board is in Maskrom mode. Run rkdeveloptool ld
    rkdeveloptool ld
    DevNo=1	Vid=0x2207,Pid=0x350a,LocationID=104	Maskrom
-Download the loader (flash helper) to init the ram and prepare the flashing environment etc. If you don't have it, you can download it from [https://dl.radxa.com/rock3/images/loader/rock-3a/rk356x_spl_loader_ddr1056_v1.10.111.bin here]
+Download the loader (flash helper) to init the ram and prepare the flashing environment etc.
-  rkdeveloptool db rk356x_spl_loader_ddr1056_v1.10.111.bin
+ rkdeveloptool db rk356x_spl_loader_ddr1056_v1.10.111.bin
-Write the GPT image to eMMC, start to write from offset '''0'''.
+Write the GPT image to eMMC, start to write from offset 0. For example.
-For example.
-  rkdeveloptool wl 0 /path/to/rock-cm3-xxx-gpt.img
+ rkdeveloptool wl 0 /path/to/radxa-cm3-io-xxx-gpt.img
 Reboot the device
-  rkdeveloptool rd
+ rkdeveloptool rd
-Now the device should boot the new image on eMMC.
+==== On Windows PC ====
-Please notice that when you want to erase eMMC on board, you can use this command. Get zero.img from [https://dl.radxa.com/rockpi4/images/others/zero.img.gz here].
+Double click the '''RKDevTool.exe''' and click button '''Download Image'''.
+[[File:Radxa-cm3-io-flash-emmc-1.png | 1000px]]
+===== Step 1: Config =====
+{| class="wikitable"
+|-
+! # || Address || Name || Path
+|-
+| 1 || 0x00000000 || Loader || /path/to/rk356x_spl_loader_ddr1056_v1.10.111.bin
+|-
+| 2 || 0x00000000 || Image || /path/to/radxa-cm3-io-xxx-gpt.img
+|}
+===== Step 2: Confirm "Found One Maskrom  Device" =====
+If your Radxa CM3 IO is in Maskrom mode and connects to PC, you can see that RKDevTool shows '''Found one MASKROM Device'''.
+===== Step 3: Run =====
+Finally, click the "run" button, and you will see the content on the right side. When RKDevTool shows '''Download image OK''', the download job is completed.
+[[File:Radxa-cm3-io-flash-emmc-2.png | 1000px]]
+=== Erase eMMC on Board ===
+==== On Linux/macOS PC ====
+Make sure that board is in Maskrom mode. Run rkdeveloptool ld.
+  rkdeveloptool ld
+  DevNo=1	Vid=0x2207,Pid=0x350a,LocationID=104	Maskrom
+Create zero.img
+  dd if=/dev/zero of=./zero.img bs=1024 count=16000
+Erase eMMC
    rkdeveloptool db rk356x_spl_loader_ddr1056_v1.10.111.bin
    rkdeveloptool wl 0 zero.img
+  rkdeveloptool rd
+==== On Windows PC ====
+Double click the '''RKDevTool.exe''' and click button "Advanced Function" to get into '''Advanced Function''' window.
+[[File:radxa-cm3-io-erase-emmc-1.png | 1000px]]
+===== Step 1: Confirm "Found One Maskrom  Device" =====
+If your Radxa CM3 IO is in Maskrom mode and connects to PC, you can see that RKDevTool shows '''Found one MASKROM Device'''.
+===== Step 2: Download RK356X Loader =====
+Choose loader rk356x_spl_loader_ddr1056_v1.10.111.bin and download it.
+[[File:radxa-cm3-io-erase-emmc-2.png | 1000px]]
+===== Step 3: Erase device =====
+Click button "EraseAll" to erase device.
+[[File:radxa-cm3-io-erase-emmc-3.png | 1000px]]
+===== Step 4: Reset device =====
+Click button "ResetDevice" to reset device.
+[[File:radxa-cm3-io-erase-emmc-4.png | 1000px]]
+Erasing job is done.
 === Troubleshooting ===
 * If you have issue with flashing via USB OTG, start a new post on the forum, https://forum.radxa.com/c/rock3.

#	Address	Name	Path
1	0x00000000	Loader	/path/to/rk356x_spl_loader_ddr1056_v1.10.111.bin
2	0x00000000	Image	/path/to/radxa-cm3-io-xxx-gpt.img

Difference between revisions of "Rock3/installusb-install-radxa-cm3-io"

Latest revision as of 02:39, 28 September 2022

Contents

Install Image to eMMC from USB port (Radxa CM3 IO)

Requirement

Install Tools&Drivers

Boot the Board to Maskrom Mode

Flash Images to eMMC on Board

On Linux/macOS PC

On Windows PC

Step 1: Config

Step 2: Confirm "Found One Maskrom Device"

Step 3: Run

Erase eMMC on Board

On Linux/macOS PC

On Windows PC

Step 1: Confirm "Found One Maskrom Device"

Step 2: Download RK356X Loader

Step 3: Erase device

Step 4: Reset device

Troubleshooting