Difference between revisions of "Rock3/installusb-install-radxa-e25"
(Created page with "{{rock3_header}} {{Languages|rock3/install/usb-install-radxa-e25}} ROCK 3 > Installation > rock3/installusb-install-radxa-e25 | Install...") |
(→Boot the board to maskrom mode) |
||
| (4 intermediate revisions by 2 users not shown) | |||
| Line 26: | Line 26: | ||
* Power off the board | * Power off the board | ||
** remove microSD card | ** remove microSD card | ||
| − | ** | + | ** make sure that your E25 version has eMMC |
| − | * Plug the USB Male A to | + | * Plug the USB Male A to A cable to ROCK E25 OTG port(the USB port), the other side to PC |
| − | * Press and hold the button | + | * Press and hold the button on the case(between the USB OTG port and USB C Power port) |
* Power on the board | * Power on the board | ||
* See usb device | * See usb device | ||
| Line 35: | Line 35: | ||
[[File:select-loader-bin.jpeg | 600px]] | [[File:select-loader-bin.jpeg | 600px]] | ||
| − | Alternatively, if you are running | + | Alternatively, if you are running Radxa Debian Linux from SD card and can access ADB, you can reboot the device to loader mode 'adb reboot bootloader' then use the rkdeveloptool to reset the device into maskrom mode 'rkdeveloptool rd 3' or Windows RKDevTool '''Switch''' button to go to maskrom mode. |
=== Install to eMMC via USB === | === Install to eMMC via USB === | ||
| Line 62: | Line 62: | ||
=== Troubleshooting === | === Troubleshooting === | ||
| + | * If programming the image to EMMC fails | ||
| + | ** Check if the second line number on your CPU starts with SB, if it starts with SB, please use the following loader to burn and try to burn again as above | ||
| + | [[File:e25-mode-SBXX.png |400px]] | ||
| + | ** [https://dl.radxa.com/rock3/images/loader/rk356x_spl_loader_ddr1056_v1.12.109_no_check_todly.bin rk356x_loader_no_check_todly] | ||
| − | Check [[rock3/FAQs |ROCK 3 FAQs]] first, if it doesn't help, start a new post on the forum https://forum.radxa.com/c/rock3. | + | * Check [[rock3/FAQs |ROCK 3 FAQs]] first, if it doesn't help, start a new post on the forum https://forum.radxa.com/c/rock3. |
Latest revision as of 12:29, 6 April 2023
ROCK 3 > Installation > Install to eMMC from USB port (Radxa E25)
Radxa E25 supports maskrom mode, which is a special running mode the CPU is waiting for command from USB OTG port. The PC tool we use to communicate with Radxa E25 in maskrom mode is rkdevelop tool, an open source tool by Rockchip.
Contents
Requirement
- Radxa E25 (with Radxa CM3 PLUS)
- 5V Type-C Power adapter
- USB Male A to USB Male A.
- Two port is Male A type.
- Hardware connection
Install Tools&Drivers
Please check this guide, Install rockchip flash tools under Windows/Linux/MacOS PC.
Boot the board to maskrom mode
To boot ROCK E25 into maskrom mode is simple:
- Power off the board
- remove microSD card
- make sure that your E25 version has eMMC
- Plug the USB Male A to A cable to ROCK E25 OTG port(the USB port), the other side to PC
- Press and hold the button on the case(between the USB OTG port and USB C Power port)
- Power on the board
- See usb device
- For Linux/macOS: lsusb result: Bus 001 Device 112: ID 2207:350a Fuzhou Rockchip Electronics Company
- For Windows: Open RKDevTool and you would see the device is in "maskrom mode".
Alternatively, if you are running Radxa Debian Linux from SD card and can access ADB, you can reboot the device to loader mode 'adb reboot bootloader' then use the rkdeveloptool to reset the device into maskrom mode 'rkdeveloptool rd 3' or Windows RKDevTool Switch button to go to maskrom mode.
Install to eMMC via USB
On your PC, run the rkdeveloptool
rkdeveloptool ld DevNo=1 Vid=0x2207,Pid=0x350a,LocationID=104 Maskrom
Download the loader (flash helper) to init the ram and prepare the flashing environment etc. If you don't have it, you can download it from here
rkdeveloptool db rk356x_spl_loader_ddr1056_v1.06.110.bin
Write the GPT image to eMMC, start to write from offset 0. For example.
rkdeveloptool wl 0 /path/to/radxa-e25-xxx-gpt.img
Please note that you can use zero.img instead of radxa-e25-xxx-gpt.img when erasing eMMC on board.
Reboot the device
rkdeveloptool rd
Now the device should boot the new image on eMMC.
Troubleshooting
- If programming the image to EMMC fails
- Check if the second line number on your CPU starts with SB, if it starts with SB, please use the following loader to burn and try to burn again as above
- Check ROCK 3 FAQs first, if it doesn't help, start a new post on the forum https://forum.radxa.com/c/rock3.