Difference between revisions of "RockpiS/network-management"

Latest revision as of 09:21, 8 September 2021

    ROCK Pi S >  Network Management

This guide describes how to manage the network on ROCK Pi S running Ubuntu system.

Part 1: Set Ethernet static IP Address

Install some dependency packages

root@rockpis:~# apt-get install -y netplan.io

Create file, /etc/netplan/01-ethernet.yaml. If there is no /etc/netplan folder, create it.

root@rockpis:~# touch /etc/netplan/01-ethernet.yaml

Add the following contents to the file, /etc/netplan/01-ethernet.yaml and save it.

root@rockpis:~# cat /etc/netplan/01-ethernet.yaml 
network:
  version: 2
  renderer: networkd
  ethernets:
    eth0:
      addresses:
        - 192.168.1.200/24
      gateway4: 192.168.1.1
      nameservers:
        addresses:
          - "192.168.1.1"
          - "8.8.8.8"

Run the commands below to apply your changes.

root@rockpis:~# netplan apply

To validate that your changes are apply, run the commands below to view the IP address configuration detals.

root@rockpis:~# ip addr show dev eth0

It should display similar lines like the one below:

root@rockpis:~# ip addr show dev eth0
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UNKNOWN group default qlen 1000
    link/ether c2:68:e0:7c:9b:09 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.200/24 brd 192.168.1.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 fe80::c068:e0ff:fe7c:9b09/64 scope link 
       valid_lft forever preferred_lft forever

Part 2: Set Wi-Fi static IP Address

root@rockpis:~# cat /etc/netplan/02-wireless.yaml 
network:
  version: 2
  renderer: networkd
  wifis:
    wlan0:
      dhcp4: no
      dhcp6: no
      addresses: [192.168.1.220/24]
      gateway4: 192.168.1.1
      nameservers:
        addresses: [192.168.1.1, 8.8.8.8]
      access-points:
        "rockpi-2.4g":
          password: "rockpistar"

Run the commands below to apply the changes.

root@rockpis:~# netplan apply

Validate that your changes are apply.

root@rockpis:~# ip addr show dev wlan0
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether 4a:33:14:54:4a:03 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.220/24 brd 192.168.1.255 scope global wlan0
       valid_lft forever preferred_lft forever

Troubleshooting

Refer Troubleshooting page
Post your issue on the forum: https://forum.radxa.com/c/rockpiS

@@ Line 3: / Line 3: @@
 {{Languages|rockpiS/dev/usbnet}}
-     [[rockpiS | ROCK Pi S]] > [[RockpiS/network-management | ROCK Pi S Network Management]]
+     [[rockpiS | ROCK Pi S]] > [[RockpiS/network-management | Network Management]]
-This guide describes how to manage the network on ROCK Pi S.
+This guide describes how to manage the network on ROCK Pi S running Ubuntu system.
-=== Introduction ===
+=== Part 1: Set Ethernet static IP Address ===
-Rockpis static address settings.First, install some dependency packages
-    sudo apt-get install netplan.io
+Install some dependency packages
-Create the '''01-netcfg.yaml'''  file in the folder /etc/netplan. If there is no netplan folder, you need to create.
-    sudo mkdir /etc/netplan
+ root@rockpis:~# apt-get install -y netplan.io
-    sudo touch /etc/netplan/01-netcfg.yaml
-Add the following to the file '''01-netcfg.yaml'''
+Create file, /etc/netplan/01-ethernet.yaml. If there is no /etc/netplan folder, create it.
-   rock@rockpis:/etc/netplan$ cat 01-netcfg.yaml
-    network:
+ root@rockpis:~# touch /etc/netplan/01-ethernet.yaml
+Add the following contents to the file, /etc/netplan/01-ethernet.yaml and save it.
+<pre>
+root@rockpis:~# cat /etc/netplan/01-ethernet.yaml
+network:
    version: 2
    renderer: networkd
@@ Line 21: / Line 27: @@
      eth0:
        addresses:
-         - 192.168.2.135/24
+         - 192.168.1.200/24
-       gateway4: 192.168.2.1
+       gateway4: 192.168.1.1
        nameservers:
-           search: [mydomain, otherdomain]
+        addresses:
-          addresses: [192.168.2.1, 255.255.255.0]
+           - "192.168.1.1"
+          - "8.8.8.8"
+</pre>
+Run the commands below to apply your changes.
+ root@rockpis:~# netplan apply
+To validate that your changes are apply, run the commands below to view the IP address configuration detals.
+ root@rockpis:~# ip addr show dev eth0
+It should display similar lines like the one below:
+<pre>
+root@rockpis:~# ip addr show dev eth0
+: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UNKNOWN group default qlen 1000
+    link/ether c2:68:e0:7c:9b:09 brd ff:ff:ff:ff:ff:ff
+    inet 192.168.1.200/24 brd 192.168.1.255 scope global eth0
+       valid_lft forever preferred_lft forever
+    inet6 fe80::c068:e0ff:fe7c:9b09/64 scope link
+       valid_lft forever preferred_lft forever
+</pre>
+=== Part 2: Set Wi-Fi static IP Address ===
+<pre>
+root@rockpis:~# cat /etc/netplan/02-wireless.yaml
+network:
+  version: 2
+  renderer: networkd
+  wifis:
+    wlan0:
+      dhcp4: no
+      dhcp6: no
+      addresses: [192.168.1.220/24]
+      gateway4: 192.168.1.1
+      nameservers:
+        addresses: [192.168.1.1, 8.8.8.8]
+      access-points:
+        "rockpi-2.4g":
+          password: "rockpistar"
+</pre>
+Run the commands below to apply the changes.
+ root@rockpis:~# netplan apply
+Validate that your changes are apply.
-Execute the following command for the configuration to take effect
+<pre>
-    sudo netplan apply
+root@rockpis:~# ip addr show dev wlan0
-then reboot,IP address is what you set.
+: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
+    link/ether 4a:33:14:54:4a:03 brd ff:ff:ff:ff:ff:ff
+    inet 192.168.1.220/24 brd 192.168.1.255 scope global wlan0
+       valid_lft forever preferred_lft forever
+</pre>
 === Troubleshooting ===