Difference between revisions of "Rockpi4/hardware/revision"
RadxaYuntian (Talk | contribs) (→v1.2) |
|||
| (16 intermediate revisions by 3 users not shown) | |||
| Line 4: | Line 4: | ||
[[rockpi4 | ROCK Pi 4]] > [[rockpi4/hardware | Hardware]] > [[rockpi4/hardware/revision | Hardware Revision]] | [[rockpi4 | ROCK Pi 4]] > [[rockpi4/hardware | Hardware]] > [[rockpi4/hardware/revision | Hardware Revision]] | ||
| − | There are | + | There are three models of ROCK Pi 4, model A, model B and model C. Model A is a stripped down version of model B. Model C is an enhanced version of model B. The differences are: |
| − | * Model A doesn't have wifi/bt model(ap6256) | + | * Model A vs. Model B |
| − | * the RJ45 connector on model A doesn't support PoE | + | ** Model A doesn't have wifi/bt model(ap6256) |
| − | * Model A doesn't have the 4Pin PoE header | + | ** the RJ45 connector on model A doesn't support PoE |
| + | ** Model A doesn't have the 4Pin PoE header | ||
| + | |||
| + | * Model B vs. Model C | ||
| + | ** Model C adds one additional mini DP port based on model B | ||
| + | ** Model C changes the HDMI connector from type A to type D(micro HDMI) | ||
==Change lists== | ==Change lists== | ||
| − | === V1.3 === | + | ===Model A | B=== |
| + | ==== V1.3 ==== | ||
This is the first MP version, the key features are: | This is the first MP version, the key features are: | ||
* User type C for power, adds QC&PD trigger IC | * User type C for power, adds QC&PD trigger IC | ||
| Line 18: | Line 24: | ||
* On board wifi antenna | * On board wifi antenna | ||
| − | === V1.4 === | + | ==== V1.4 ==== |
V1.4 is a slightly updates based on the V1.3, solves the issues reported by users. The schematic is the same as V1.3. | V1.4 is a slightly updates based on the V1.3, solves the issues reported by users. The schematic is the same as V1.3. | ||
| Line 26: | Line 32: | ||
* Change user status LED from red to blue(blinking red led is confusing for some user) | * Change user status LED from red to blue(blinking red led is confusing for some user) | ||
* A 4MB(32Mbit) SPI flash is pasted by default, for future SPI booting support | * A 4MB(32Mbit) SPI flash is pasted by default, for future SPI booting support | ||
| + | |||
| + | ==== V1.5 ==== | ||
| + | |||
| + | To fight with the global chips shortage, replace the short of supply chips. | ||
| + | |||
| + | * ROCK Pi 4A and 4B now share the same PCB(ROCK Pi 4), no wifi/bt module pasted on 4A, RJ45 has no PoE capability on 4A | ||
| + | * Ethernet phy changed from RTL8211E to RLT8211F(no software change required) | ||
| + | * Change the headphone detect circuit, use the mic from HP jack by default | ||
| + | * QC/PD protocol trigger chip changed to CH224D | ||
| + | |||
| + | ==== V1.6(4A+/4B+) ==== | ||
| + | * 4A+ and 4B+ now share the same PCB(ROCK Pi 4 Plus), no wifi/bt module pasted on 4A+, RJ45 has no PoE capability on 4A+ | ||
| + | * Add USB C input voltage measure from SoC ADC | ||
| + | * Add EEPROM (BL24C16A) for mac address and serial no. | ||
| + | * eMMC socket changed to on board chips | ||
| + | * Three buttons are soldered by default.(1: Maskrom 2: Reset 3: Recovery) See [[https://wiki.radxa.com/File:Rockpi4bplus_key.jpg picture here]]. | ||
| + | |||
| + | ==== V1.72(4A+/4B+) ==== | ||
| + | |||
| + | To fight with the global chips shortage, replace the short of supply chips. | ||
| + | |||
| + | * Ethernet phy changed from RTL8211E to RLT8211F(no software change required) | ||
| + | * QC/PD protocol trigger chip changed to CH224D | ||
| + | |||
| + | ==== V1.73(4A+/4B+) ==== | ||
| + | * Optimize the headphone jack footprint for manufacturing | ||
| + | * '''Board manufactured after 2022-08-05 will have SPI unpopulated.''' This include future revisions. | ||
| + | |||
| + | === Model C === | ||
| + | ==== v1.2==== | ||
| + | * change to a more tight micro HDMI connector | ||
| + | |||
| + | === Model C+ === | ||
| + | ==== v1.2==== | ||
| + | * Initial version | ||
| + | |||
| + | ==== v1.4==== | ||
| + | * Remove M.2 connector | ||
Latest revision as of 11:36, 5 May 2023
ROCK Pi 4 > Hardware > Hardware Revision
There are three models of ROCK Pi 4, model A, model B and model C. Model A is a stripped down version of model B. Model C is an enhanced version of model B. The differences are:
- Model A vs. Model B
- Model A doesn't have wifi/bt model(ap6256)
- the RJ45 connector on model A doesn't support PoE
- Model A doesn't have the 4Pin PoE header
- Model B vs. Model C
- Model C adds one additional mini DP port based on model B
- Model C changes the HDMI connector from type A to type D(micro HDMI)
Contents
Change lists
Model A | B
V1.3
This is the first MP version, the key features are:
- User type C for power, adds QC&PD trigger IC
- LPDDR4 for 1/2/4GB ram
- Use odroid compatible eMMC socket as storage
- On board wifi antenna
V1.4
V1.4 is a slightly updates based on the V1.3, solves the issues reported by users. The schematic is the same as V1.3.
- Changes the USB3 OTG label to simple L/H for Host/Device
- Add external wifi antenna option, not soldered by default
- Change the headphone footprint to through hole leg one
- Change user status LED from red to blue(blinking red led is confusing for some user)
- A 4MB(32Mbit) SPI flash is pasted by default, for future SPI booting support
V1.5
To fight with the global chips shortage, replace the short of supply chips.
- ROCK Pi 4A and 4B now share the same PCB(ROCK Pi 4), no wifi/bt module pasted on 4A, RJ45 has no PoE capability on 4A
- Ethernet phy changed from RTL8211E to RLT8211F(no software change required)
- Change the headphone detect circuit, use the mic from HP jack by default
- QC/PD protocol trigger chip changed to CH224D
V1.6(4A+/4B+)
- 4A+ and 4B+ now share the same PCB(ROCK Pi 4 Plus), no wifi/bt module pasted on 4A+, RJ45 has no PoE capability on 4A+
- Add USB C input voltage measure from SoC ADC
- Add EEPROM (BL24C16A) for mac address and serial no.
- eMMC socket changed to on board chips
- Three buttons are soldered by default.(1: Maskrom 2: Reset 3: Recovery) See [picture here].
V1.72(4A+/4B+)
To fight with the global chips shortage, replace the short of supply chips.
- Ethernet phy changed from RTL8211E to RLT8211F(no software change required)
- QC/PD protocol trigger chip changed to CH224D
V1.73(4A+/4B+)
- Optimize the headphone jack footprint for manufacturing
- Board manufactured after 2022-08-05 will have SPI unpopulated. This include future revisions.
Model C
v1.2
- change to a more tight micro HDMI connector
Model C+
v1.2
- Initial version
v1.4
- Remove M.2 connector