Difference between revisions of "RockpiS/dev/sdnand-install"

Latest revision as of 10:30, 3 July 2024

    ROCK Pi S >  Installation >  Install on SD NAND Flash

install from linux

Install on SD NAND Flash

ROCK Pi S supports maskrom mode, which is a special running mode the CPU is waiting for command from USB OTG port. The PC tool we use to communicate with ROCK Pi S in maskrom mode is rkdeveloptool, an open source tool by Rockchip.

Requirement

ROCK Pi S mainboard
ROCK Pi S model with SD Nand on board(Check models)
USB Male A to Male C cable
Linux or other OS image for ROCK Pi S (< 1GB)

ROCK Pi S hardware details can be found here

Step 1: Make sure rkdeveloptool is set up on host computer

Follow https://wiki.radxa.com/RockpiS/dev/otg to install rkdeveloptool tool.

Step 2: Boot the board to maskrom mode

The ROCK Pi S Board presents two buttons. They are Reset key and Maskrom key.

The Reset button serves as the hardware reset button. short press and release the button,the system will be rebooted.

The Maskrom Button is for firmware flash/upgrade.

To boot ROCK Pi S into maskrom mode, you need

plug the ROCK Pi S to Linux desktop with the USB Male A to Male C cable
press and hold the maskrom key, then short press reset key
release maskrom key(important!)

Now on your Linux PC, lsusb command shows the following usb devices

 Bus 001 Device 014: ID 2207:330e

It means the device is in maskrom mode now.

Now we can proceed the next step to flash.

Step 3: Write to SD Nand via USB

On your PC, run the rkdeveloptool

 rkdeveloptool ld        # List the device
 DevNo=1	Vid=0x2207,Pid=0x330e,LocationID=104	Maskrom

Download the loader (flash helper, important) to init the ram and prepare the flashing environment etc. If you don't have it, you can download it from here

 sudo rkdeveloptool db /path/to/rk3308_loader_ddr589MHz_uart0_m0_v2.06.136sd.bin  # will output: Downloading bootloader succeeded.
 sudo rkdeveloptool wl 0 /path/to/system.img    # will output: Write LBA from file (100%)
 sudo rkdeveloptool rd    # will output: Reset Device OK.

Now the device should boot from the SD Nand now.

Optional: Erase image on SD Nand

This step serves for someone who want to boot ROCK Pi S on uSD Card when there is one system image on SD Nand.

To erase images on SD Nand, just need the following steps.

Firstly, follow Step 2: Boot the board to maskrom mode, Case 2: Update system image on SD Nand to boot ROCK Pi S to maskrom mode.

Secondly, on your Linux PC, create zero.img.

 dd if=/dev/zero of=./zero.img bs=4M count=10

Thirdly, flash zero.img to SD Nand.

 rkdeveloptool db /path/to/rk3308_loader_ddr589MHz_uart0_m0_v2.06.136sd.bin
 rkdeveloptool wl 0 zero.img
 rkdeveloptool rd    # will output: Reset Device OK.

Finally, on your Linux PC, lsusb command show show the following usb devices

 Bus 001 Device 014: ID 2207:330e

It means the SD Nand is erased successfully.

install from windows

Firstly, make sure that rockpis is in maskrom mode

secondly, select rk3308_loader*.bin listed above, and ROCK Pi S system image. If you don't have the system image, you can download it from here.

lastly, if see “Download image ok”, that means you are sucessfully install on SD nand from Windows .

FAQs

Troubleshooting

If you have issue with flashing via USB OTG, start a new post on the forum. https://forum.radxa.com/c/dev

@@ Line 4: / Line 4: @@
      [[rockpiS | ROCK Pi S]] > [[rockpiS/install | Installation]] > [[RockpiS/dev/sdnand-install  | Install on SD NAND Flash]]
+== install from linux ==
 ===Install on SD NAND Flash===
@@ Line 12: / Line 14: @@
 * ROCK Pi S mainboard
-* SD Nand soldered on ROCK Pi S
+* ROCK Pi S model with [[RockpiS/hardware/SDNAND | SD Nand]] on board(Check [[RockpiS/hardware/models |models]])
 * USB Male A to Male C cable
-* System image (< 1GB)
+* Linux or other OS image for ROCK Pi S (< 1GB)
-Notes
+ROCK Pi S hardware details can be found [https://wiki.radxa.com/RockpiS/hardware/rockpiS here]
-System images are [https://dl.radxa.com/rockpis/images/debian/ here].
-ROCK Pi S hardware details see [https://wiki.radxa.com/RockpiS/hardware/rockpiS here]
 ====Step 1: Make sure rkdeveloptool is set up on host computer====
@@ Line 28: / Line 26: @@
 ====Step 2: Boot the board to maskrom mode====
-=====Case 1: Empty SD Nand=====
+The ROCK Pi S Board presents two buttons. They are Reset key and Maskrom key.
-To boot ROCK Pi S into maskrom mode is simple, you don't need to press any key.
-* Power off the board and remove any bootable storage media, microSD card.
+[[File:Keys.jpeg | 300px]]
-* Plug the USB Male A to Male C cable to ROCK Pi S OTG port(Type C port), the other side to PC
-* Power on the board
-=====Case 2: Update system image on SD Nand=====
-The ROCK Pi S Board presents two buttons. They are Reset key and Maskrom key.
 The Reset button serves as the hardware reset button. short press and release the button,the system will be rebooted.
@@ Line 48: / Line 38: @@
 * plug the ROCK Pi S to Linux desktop with the USB Male A to Male C cable
 * press and hold the maskrom key, then short press reset key
-* release maskrom key(important!)
+* release maskrom key('''important'''!)
 Now on your Linux PC, lsusb command shows the following usb devices
@@ Line 58: / Line 48: @@
 Now we can proceed the next step to flash.
-=====Step 3: Write to SD Nand via USB=====
+====Step 3: Write to SD Nand via USB====
 On your PC, run the rkdeveloptool
@@ Line 65: / Line 55: @@
    DevNo=1	Vid=0x2207,Pid=0x330e,LocationID=104	Maskrom
-Download the loader (flash helper, important) to init the ram and prepare the flashing environment etc. If you don't have it, you can download it from [https://dl.radxa.com/rockpis/images/loader/rk3308_loader_uart0_m0_emmc_port_support_sd_20190717.bin here]
+Download the loader (flash helper, important) to init the ram and prepare the flashing environment etc. If you don't have it, you can download it from [https://dl.radxa.com/rockpis/images/loader/rk3308_loader_ddr589MHz_uart0_m0_v2.06.136sd.bin here]
-   sudo rkdeveloptool db /path/to/rk3308_loader_uart0_m0_emmc_port_support_sd_20190717.bin  # will output: Downloading bootloader succeeded.
+   sudo rkdeveloptool db /path/to/rk3308_loader_ddr589MHz_uart0_m0_v2.06.136sd.bin  # will output: Downloading bootloader succeeded.
    sudo rkdeveloptool wl 0 /path/to/system.img    # will output: Write LBA from file (100%)
    sudo rkdeveloptool rd    # will output: Reset Device OK.
@@ Line 73: / Line 63: @@
 Now the device should boot from the SD Nand now.
-=====Step 4: Erase image on SD Nand=====
+====Optional: Erase image on SD Nand====
 This step serves for someone who want to boot ROCK Pi S on uSD Card when there is one system image on SD Nand.
@@ Line 87: / Line 77: @@
 Thirdly, flash zero.img to SD Nand.
-   rkdeveloptool db /path/to/rk3308_loader_uart0_m0_emmc_port_support_sd_20190717.bin
+   rkdeveloptool db /path/to/rk3308_loader_ddr589MHz_uart0_m0_v2.06.136sd.bin
    rkdeveloptool wl 0 zero.img
    rkdeveloptool rd    # will output: Reset Device OK.
@@ Line 96: / Line 86: @@
 It means the SD Nand is erased successfully.
+== install from windows ==
+Firstly, make sure that rockpis is in maskrom mode
+secondly, select rk3308_loader*.bin listed above, and ROCK Pi S system image. If you don't have the system image, you can download it from [https://github.com/radxa/rock-pi-s-images-released/releases/download/rock-pi-s-v20210924/rockpis_debian_buster_server_arm64_20210924_0412-gpt.img.gz here].
+[[File:nand.png |400px]]
+lastly, if see “Download image ok”, that means you are sucessfully install on SD nand from Windows .
 ====FAQs====