Difference between revisions of "Rockpi4/hardware/display"
(→Rotatation) |
|||
| (7 intermediate revisions by the same user not shown) | |||
| Line 3: | Line 3: | ||
[[rockpi4 | ROCK Pi 4]] > [[rockpi4/hardware | Hardware]] > [[rockpi4/hardware/display | Display]] | [[rockpi4 | ROCK Pi 4]] > [[rockpi4/hardware | Hardware]] > [[rockpi4/hardware/display | Display]] | ||
| − | |||
| − | |||
== HDMI Display == | == HDMI Display == | ||
Most HDMI display with USB touch works out of box. | Most HDMI display with USB touch works out of box. | ||
| + | == Radxa Display 10HD == | ||
| + | |||
| + | === Hardware connection === | ||
| + | |||
| + | [[File:rockpi4cplus-radxa-display-10hd.jpeg | 500px ]] | ||
| + | |||
| + | === Software configuration === | ||
| + | |||
| + | Edit file /boot/hw_intfc.conf and uncomment the following lines. And then reboot the device. | ||
| + | |||
| + | # enable rk3399-rock-pi-4c-plus-radxa-10p1inch-display | ||
| + | #intfc:dtoverlay=rk3399-rock-pi-4c-plus-radxa-10p1inch-display | ||
| + | |||
| + | ==== Rotation ==== | ||
| + | |||
| + | Add the following lines to the end of file /etc/X11/xorg.conf.d/20-modesetting.conf | ||
| + | |||
| + | <pre> | ||
| + | ### Valid values for rotation are "normal", "left", "right" | ||
| + | Section "Monitor" | ||
| + | Identifier "Default Monitor" | ||
| + | Option "Rotate" "normal" | ||
| + | EndSection | ||
| + | </pre> | ||
== MIPI DSI Display == | == MIPI DSI Display == | ||
| Line 14: | Line 36: | ||
The official [https://www.raspberrypi.org/products/raspberry-pi-touch-display/ Raspberry Pi 7 inch Touch Display] works on ROCK Pi 4. | The official [https://www.raspberrypi.org/products/raspberry-pi-touch-display/ Raspberry Pi 7 inch Touch Display] works on ROCK Pi 4. | ||
| + | ==== Usage on Radxa official Linux system ==== | ||
| + | Edit file /boot/hw_intfc.conf and uncomment the following lines. And then reboot the device. | ||
| + | |||
| + | #enable raspberry pi official 7 inch LCD support | ||
| + | intfc:dtoverlay=raspberrypi-7-inch-lcd | ||
== Waveshare 3.5 inch LCD == | == Waveshare 3.5 inch LCD == | ||
| Line 34: | Line 61: | ||
intfc:dtoverlay=spi1-waveshare35b-v2 | intfc:dtoverlay=spi1-waveshare35b-v2 | ||
| − | |||
To install the required display support packages enter the following command lines: | To install the required display support packages enter the following command lines: | ||
| Line 41: | Line 67: | ||
$ sudo apt-get install xserver-xorg-video-fbdev | $ sudo apt-get install xserver-xorg-video-fbdev | ||
| − | + | Backup and clean the contents of file, /etc/X11/xorg.conf.d/20-modesetting.conf. Then add the following lines to it: | |
Section "Device" | Section "Device" | ||
Identifier "Rockchip Graphics" | Identifier "Rockchip Graphics" | ||
| Line 69: | Line 95: | ||
$ sudo apt-get install xserver-xorg-video-fbdev | $ sudo apt-get install xserver-xorg-video-fbdev | ||
| − | + | Backup and clean the contents of file, /etc/X11/xorg.conf.d/20-modesetting.conf. Then add the following lines to it: | |
Section "Device" | Section "Device" | ||
Identifier "Rockchip Graphics" | Identifier "Rockchip Graphics" | ||
| Line 83: | Line 109: | ||
== Troubleshooting == | == Troubleshooting == | ||
| − | * If you have issue with | + | * If you have issue with Display, start a new post on the forum. https://forum.radxa.com/ |
Latest revision as of 02:37, 24 June 2022
ROCK Pi 4 > Hardware > Display
Contents
HDMI Display
Most HDMI display with USB touch works out of box.
Radxa Display 10HD
Hardware connection
Software configuration
Edit file /boot/hw_intfc.conf and uncomment the following lines. And then reboot the device.
# enable rk3399-rock-pi-4c-plus-radxa-10p1inch-display #intfc:dtoverlay=rk3399-rock-pi-4c-plus-radxa-10p1inch-display
Rotation
Add the following lines to the end of file /etc/X11/xorg.conf.d/20-modesetting.conf
### Valid values for rotation are "normal", "left", "right"
Section "Monitor"
Identifier "Default Monitor"
Option "Rotate" "normal"
EndSection
MIPI DSI Display
Raspberry Pi 7 inch Touch Display
The official Raspberry Pi 7 inch Touch Display works on ROCK Pi 4.
Usage on Radxa official Linux system
Edit file /boot/hw_intfc.conf and uncomment the following lines. And then reboot the device.
#enable raspberry pi official 7 inch LCD support intfc:dtoverlay=raspberrypi-7-inch-lcd
For waveshare LCD, both display and touch are two spi devices.
Due to the hardware limitation with only one CS for spi1 of ROCK Pi 4, waveshare LCD only support display but touch.
Wavashare LCD works as a framebuffer device.
Model B v2
Update kernel(>=4.4.154-83) and rockpi4-dtbo(>=0.9) pacakge.
When use it , add the following lines to the hardware interface config file /boot/hw_intfc.conf :
intfc:uart4=off
intfc:spi1=on
intfc:dtoverlay=spi1-waveshare35b-v2
To install the required display support packages enter the following command lines:
$ sudo apt-get update $ sudo apt-get install xserver-xorg-video-fbdev
Backup and clean the contents of file, /etc/X11/xorg.conf.d/20-modesetting.conf. Then add the following lines to it:
Section "Device"
Identifier "Rockchip Graphics"
Driver "fbdev"
Option "fbdev" "/dev/fb1"
Option "DRI" "2"
EndSection
You need to checkout the device, "/dev/fb1" or "/dev/fb0".
Reboot ROCK Pi 4.
Model C
Update kernel(>=4.4.154-83) and rockpi4-dtbo(>=0.9) pacakge.
When use it , add the following lines to the hardware interface config file /boot/hw_intfc.conf :
intfc:uart4=off intfc:spi1=on intfc:dtoverlay=spi1-waveshare35c
To install the required display support packages enter the following command lines:
$ sudo apt-get update $ sudo apt-get install xserver-xorg-video-fbdev
Backup and clean the contents of file, /etc/X11/xorg.conf.d/20-modesetting.conf. Then add the following lines to it:
Section "Device"
Identifier "Rockchip Graphics"
Driver "fbdev"
Option "fbdev" "/dev/fb1"
Option "DRI" "2"
EndSection
You need to checkout the device, "/dev/fb1" or "/dev/fb0".
Reboot ROCK Pi 4.
Troubleshooting
- If you have issue with Display, start a new post on the forum. https://forum.radxa.com/