|
|
| Line 1: |
Line 1: |
| − | {{rock3_header}}
| + | #REDIRECT [[Rock3/CM3/e23/getting_started | Getting started]] |
| − | {{Languages|rock3/getting_started/radxa-e23}}
| + | |
| − | | + | |
| − | | + | |
| − | __TOC__
| + | |
| − | | + | |
| − | = Getting Started =
| + | |
| − | | + | |
| − | This guide is designed for Radxa E23 enthusiast. The purpose is to learn about Radxa E23 as well as how to prepare and set up for basic use.
| + | |
| − | When you get a board, you need to know what model it is and which hardware version it is.
| + | |
| − | The information is printed in the top side of the board.
| + | |
| − | We will introduce the board information as much as possible.
| + | |
| − | | + | |
| − | == Close look of Radxa E23 ==
| + | |
| − | * Radxa E23 front view
| + | |
| − | * Radxa E23 front with an angle view
| + | |
| − | * Radxa E23 back view
| + | |
| − | | + | |
| − | == <span id="get_start_specs"></span> Features ==
| + | |
| − | | + | |
| − | {| class="wikitable"
| + | |
| − | ! Model
| + | |
| − | ! colspan="1" width=80% | Radxa E23
| + | |
| − | |-
| + | |
| − | !SoC<br><br>CPU<br>GPU<br>NPU
| + | |
| − | | colspan="2" | '''RK3566''' <br><br>Quad-core Cortex-A55, freqency 2Ghz<br>
| + | |
| − | Mali G52<br>
| + | |
| − | 0.8TOPS NPU
| + | |
| − | |-
| + | |
| − | ! Memory
| + | |
| − | | colspan="2" | 1GB, 2GB, 4GB or 8GB LPDDR4 (depending on SoM variant)
| + | |
| − | |-
| + | |
| − | ! Storage
| + | |
| − | | colspan="2" | eMMC (8/16/32/64/128GB)<br>μSD card (μSD slot supports up to 128 GB μSD card)<br>one SPI Nor Flash<br>one EEPROM
| + | |
| − | |-
| + | |
| − | ! Audio
| + | |
| − | | colspan="2" | 3.5mm jack with mic<br>HD codec that supports up to 24-bit/96KHz audio.
| + | |
| − | |-
| + | |
| − | ! Wireless
| + | |
| − | | colspan="2" | Optional wireless LAN, 2.4GHz and 5.0GHz IEEE 802.11b/g/n/ac wireless.<br>Bluetooth 5.0, BLE with external antenna (depending on SoM variant).
| + | |
| − | |-
| + | |
| − | ! USB
| + | |
| − | | colspan="2" | USB 3.0 HOST X1<br>USB 2.0 OTG X1(USB C)<br>USB 2.0 HOST(40P GPIO)
| + | |
| − | |-
| + | |
| − | ! Ethernet
| + | |
| − | | colspan="2" | 1GbE LAN X1<br>2.5GbE LAN X1(PoE Support)
| + | |
| − | |-
| + | |
| − | ! IO
| + | |
| − | | colspan="2" | 40-pin expansion header
| + | |
| − | |-
| + | |
| − | ! LED
| + | |
| − | | colspan="2" | Green LED X1<br>RGB LED X1
| + | |
| − | |-
| + | |
| − | ! Key
| + | |
| − | | colspan="2" | Power Key X1<br>Recovery Key X1
| + | |
| − | |-
| + | |
| − | ! Power
| + | |
| − | | colspan="2" | USB Type-C DC 5V
| + | |
| − | |-
| + | |
| − | ! Size
| + | |
| − | | colspan="2" | 2.5x2.2 inch(56x65mm)
| + | |
| − | |}
| + | |
| − | | + | |
| − | == What you need ==
| + | |
| − | | + | |
| − | === Necessary ===
| + | |
| − | * Radxa E23
| + | |
| − | | + | |
| − | * One of the Storage media below:
| + | |
| − | ** microSD, larger than 8GB.
| + | |
| − | ** eMMC, larger than 8GB.
| + | |
| − | | + | |
| − | * Power supply
| + | |
| − | ** Radxa E23 is powered by Type-C port. Input voltage is '''5V only'''.
| + | |
| − | | + | |
| − | *USB Male A to Male A cable
| + | |
| − | **If you want write image on ROCK 3 from USB OTG port or use fastboot/adb commands you need an USB Male A to Male A cable to connect ROCK 3 and PC.
| + | |
| − | | + | |
| − | === Optional ===
| + | |
| − | * microSD Card Reader
| + | |
| − | ** For flashing the image into microSD Card
| + | |
| − | | + | |
| − | * USB to TTL serial cable
| + | |
| − | ** This is needed for serial console.
| + | |
| − | | + | |
| − | * Ethernet cable
| + | |
| − | ** Radxa E23 supports Internet access via WIFI or Ethernet.
| + | |
| − | ** An Ethernet cable is used to connect your Radxa E23 to a local network and the Internet.
| + | |
| − | | + | |
| − | * Audio cable
| + | |
| − | ** Audio can be played through speaker or headphones using a standard 3.5mm jack.
| + | |
