Difference between revisions of "Zero/install/eMMC"
(→Linux) |
|||
| Line 120: | Line 120: | ||
==== macOS ==== | ==== macOS ==== | ||
| − | For macOS, we use amlogic boot tool to download the bootloader and boot the Zero into the | + | For macOS, we use amlogic boot tool to download the bootloader and boot the Zero into the USB Disk mode to export the eMMC to mac as a USB Disk, then we can use dd or other tools to write images to the USB Disk(eMMC). |
===== Step 1: Install pyamlboot tool ===== | ===== Step 1: Install pyamlboot tool ===== | ||
| Line 127: | Line 127: | ||
pip3 install pyamlboot | pip3 install pyamlboot | ||
| − | ===== Step 2: | + | ===== Step 2: Erase Android if installed(optional) ===== |
| − | + | If you have Android installed on Zero before, we suggest to wipe it. Check [[zero/install/eMMC_erase#macOS |Erase eMMC]] page. If you have installed Linux or other distribution already, you can skip this step. | |
| − | + | ===== Step 3: Boot into USB Disk mode ===== | |
| − | + | Press and hold the USB boot button on Zero, plug in it to mac, '''lsusb''' should see the following: | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | Press and hold the USB boot button on Zero, plug in it to | + | |
Bus 002 Device 030: ID 1b8e:c003 Amlogic, Inc. GX-CHIP | Bus 002 Device 030: ID 1b8e:c003 Amlogic, Inc. GX-CHIP | ||
| − | Download the | + | Download the USB disk loader and run it on Zero |
| − | + | wget https://dl.radxa.com/zero/images/loader/rz-udisk-loader.bin | |
| − | + | boot-g12.py rz-fastboot-loader.bin | |
It should output: | It should output: | ||
| Line 178: | Line 170: | ||
Now lsusb should show the following device: | Now lsusb should show the following device: | ||
| − | Bus 002 Device | + | Bus 002 Device 013: ID 1b8e:2200 Amlogic, Inc. USB download gadget Serial: AMLG12A-RADXA-ZERO |
| − | + | ||
| − | + | ||
| − | + | The Zero is in USB disk mode now, your mac should popup a new USB drive. Just click Ignore. | |
| − | + | ||
| − | + | [[File:Rz-udisk-mac-popup.jpg]] | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ===== Step 4: Write image to eMMC ===== | |
| − | + | You can use dd to write the raw image to the eMMC of Zero now. | |
| − | + | sudo dd if=/path/to/image of=/dev/sdx bs=1m | |
| + | sync | ||
| − | the | + | Carefully Eject the Zero USB drive and unplug and plug the power, Zero should boot the new image now. |
Revision as of 10:29, 14 September 2021
Radxa Zero > Installation > Install image to eMMC
Contents
How to install raw images to Radxa Zero eMMC
This guide describes how to install the raw images to Radxa Zero eMMC. Raw images is compared to amlupdate format image(which is a private image format). Raw images can be mount and open on host PCs. Most of the Linux images released are raw images. Currently Android images are released in amlupdate format but this may change in the future.
Requirement
- Radxa Zero
- USB A to C cable
- A PC/laptop running Windows, Linux/macOS.
Windows
Step 1: Install drivers
Download Zagdig, install it and choose libusb-win32, then click Install Driver.
Download the Android driver from Google:
Click here to download the Google USB Driver ZIP file (ZIP)
Unzip it and right click the .inf file to install the driver.
Step 2: Use RZ USB helper to erase eMMC and boot to USB disk mode
RZ USB helper is a tool by Radxa for Windows users to manage Radxa Zero booting easier. Download it from Radxa DL.
Press and hold the USB boot button on the Zero, plug in the USB to PC, Maskrom mode should be detected.
Select the loader in the RZ_USB_Boot_Helper zip and click Run.
Click Erase to erase the eMMC completely.
Now select the RZ USB disk loader.
Step 3: Use Etcher to write images to eMMC
Download the latest Etcher and install it.
Linux
For Linux, we use amlogic boot tool to download the bootloader and boot the Zero into the USB Disk mode to export the eMMC to host PC as a USB Disk, then we can use dd or other tools to write images to the USB Disk(eMMC).
Step 1: Install pyamlboot tool
sudo apt install pip3 sudo pip3 install pyamlboot
Step 2: Erase Android if installed(optional)
If you have Android installed on Zero before, we suggest to wipe it. Check Erase eMMC page. If you have installed Linux or other distribution already, you can skip this step.
Step 3: Boot into USB Disk mode
Press and hold the USB boot button on Zero, plug in it to PC, lsusb should see the following:
Bus 002 Device 030: ID 1b8e:c003 Amlogic, Inc. GX-CHIP
Download the USB disk loader and run it on Zero
wget https://dl.radxa.com/zero/images/loader/rz-udisk-loader.bin boot-g12.py rz-fastboot-loader.bin
It should output:
Firmware Version : ROM: 3.2 Stage: 0.0 Need Password: 0 Password OK: 1 Writing rz-fastboot-loader.bin at 0xfffa0000... [DONE] Running at 0xfffa0000... [DONE] AMLC dataSize=16384, offset=65536, seq=0... [DONE] AMLC dataSize=49152, offset=393216, seq=1... [DONE] AMLC dataSize=16384, offset=229376, seq=2... [DONE] AMLC dataSize=49152, offset=245760, seq=3... [DONE] AMLC dataSize=49152, offset=294912, seq=4... [DONE] AMLC dataSize=16384, offset=65536, seq=5... [DONE] AMLC dataSize=1406320, offset=81920, seq=6... [DONE] [BL2 END]
Now lsusb should show the following device:
Bus 002 Device 013: ID 1b8e:2200 Amlogic, Inc. USB download gadget Serial: AMLG12A-RADXA-ZERO
The Zero is in USB disk mode now, your PC should popup a new USB drive.
Step 4: Write image to eMMC
You can use dd to write the Linux image to the eMMC of Zero now.
sudo dd if=/path/to/image of=/dev/sdx bs=1M sync
Carefully Eject the Zero USB drive and unplug and plug the power, Zero should boot the new image now.
macOS
For macOS, we use amlogic boot tool to download the bootloader and boot the Zero into the USB Disk mode to export the eMMC to mac as a USB Disk, then we can use dd or other tools to write images to the USB Disk(eMMC).
Step 1: Install pyamlboot tool
brew install python lsusb pip3 install pyamlboot
Step 2: Erase Android if installed(optional)
If you have Android installed on Zero before, we suggest to wipe it. Check Erase eMMC page. If you have installed Linux or other distribution already, you can skip this step.
Step 3: Boot into USB Disk mode
Press and hold the USB boot button on Zero, plug in it to mac, lsusb should see the following:
Bus 002 Device 030: ID 1b8e:c003 Amlogic, Inc. GX-CHIP
Download the USB disk loader and run it on Zero
wget https://dl.radxa.com/zero/images/loader/rz-udisk-loader.bin boot-g12.py rz-fastboot-loader.bin
It should output:
Firmware Version : ROM: 3.2 Stage: 0.0 Need Password: 0 Password OK: 1 Writing rz-fastboot-loader.bin at 0xfffa0000... [DONE] Running at 0xfffa0000... [DONE] AMLC dataSize=16384, offset=65536, seq=0... [DONE] AMLC dataSize=49152, offset=393216, seq=1... [DONE] AMLC dataSize=16384, offset=229376, seq=2... [DONE] AMLC dataSize=49152, offset=245760, seq=3... [DONE] AMLC dataSize=49152, offset=294912, seq=4... [DONE] AMLC dataSize=16384, offset=65536, seq=5... [DONE] AMLC dataSize=1406320, offset=81920, seq=6... [DONE] [BL2 END]
Now lsusb should show the following device:
Bus 002 Device 013: ID 1b8e:2200 Amlogic, Inc. USB download gadget Serial: AMLG12A-RADXA-ZERO
The Zero is in USB disk mode now, your mac should popup a new USB drive. Just click Ignore.
Step 4: Write image to eMMC
You can use dd to write the raw image to the eMMC of Zero now.
sudo dd if=/path/to/image of=/dev/sdx bs=1m sync
Carefully Eject the Zero USB drive and unplug and plug the power, Zero should boot the new image now.