Please enable javascript, or click here to visit my ecommerce web site powered by Shopify.
Jump to: navigation, search

Difference between revisions of "RockpiS/dev/sdnand-install"

< RockpiS‎ | dev
(Requirement)
(Step 4: Erase image on SD Nand)
Line 73: Line 73:
 
To erase images on SD Nand, just need the following steps.
 
To erase images on SD Nand, just need the following steps.
  
Firstly, follow '''Step 2: Boot the board to maskrom mode, Case 2: Update system image on SD Nand''' to boot ROCK Pi 4 to maskrom mode.
+
Firstly, follow '''Step 2: Boot the board to maskrom mode, Case 2: Update system image on SD Nand''' to boot ROCK Pi S to maskrom mode.
  
 
Secondly, on your Linux PC, create zero.img.
 
Secondly, on your Linux PC, create zero.img.

Revision as of 07:59, 28 October 2019

    ROCK Pi S >  Installation >  Install on SD NAND Flash

Install on SD NAND Flash

ROCK Pi S supports maskrom mode, which is a special running mode the CPU is waiting for command from USB OTG port. The PC tool we use to communicate with ROCK Pi S in maskrom mode is rkdeveloptool, an open source tool by Rockchip.

Requirement

  • ROCK Pi S mainboard
  • SD Nand soldered on ROCK Pi S
  • USB Male A to Male C cable
  • System image (< 1GB)

System images are here.

Step 1: Make sure rkdeveloptool is set up on host computer

Follow https://wiki.radxa.com/RockpiS/dev/otg to install rkdeveloptool tool.

Step 2: Boot the board to maskrom mode

Case 1: Empty SD Nand

To boot ROCK Pi S into maskrom mode is simple, you don't need to press any key.

  • Power off the board and remove any bootable storage media, microSD card.
  • Plug the USB Male A to Male C cable to ROCK Pi S OTG port(Type C port), the other side to PC
  • Power on the board
Case 2: Update system image on SD Nand

The ROCK Pi S Board presents two buttons. They are Reset key and Maskrom key.

The Reset button serves as the hardware reset button. short press and release the button,the system will be rebooted.

The Maskrom Button is for firmware flash/upgrade.

To boot ROCK Pi S into maskrom mode, you need

  • plug the ROCK Pi S to Linux desktop with the USB Male A to Male C cable
  • press and hold the maskrom key, then short press reset key
  • release maskrom key(important!)

Now on your Linux PC, lsusb command shows the following usb devices

 Bus 001 Device 014: ID 2207:330e

It means the device is in maskrom mode now.

Now we can proceed the next step to flash.

Step 3: Write to SD Nand via USB

On your PC, run the rkdeveloptool

 rkdeveloptool ld        # List the device
 DevNo=1	Vid=0x2207,Pid=0x330e,LocationID=104	Maskrom

Download the loader (flash helper, important) to init the ram and prepare the flashing environment etc. If you don't have it, you can download it from here

 sudo rkdeveloptool db /path/to/rk3308_loader_uart0_m0_emmc_port_support_sd_20190717.bin  # will output: Downloading bootloader succeeded.
 sudo rkdeveloptool wl 0 /path/to/system.img    # will output: Write LBA from file (100%)
 sudo rkdeveloptool rd    # will output: Reset Device OK.

Now the device should boot from the SD Nand now.

Step 4: Erase image on SD Nand

To erase images on SD Nand, just need the following steps.

Firstly, follow Step 2: Boot the board to maskrom mode, Case 2: Update system image on SD Nand to boot ROCK Pi S to maskrom mode.

Secondly, on your Linux PC, create zero.img.

 dd if=/dev/zero of=./zero.img bs=4M count=10

Thirdly, flash zero.img to SD Nand.

 rkdeveloptool db /path/to/rk3308_loader_uart0_m0_emmc_port_support_sd_20190717.bin
 rkdeveloptool wl 0 zero.img
 rkdeveloptool rd    # will output: Reset Device OK.

Finally, on your Linux PC, lsusb command show show the following usb devices

 Bus 001 Device 014: ID 2207:330e

It means the SD Nand is erased successfully.

FAQs

Troubleshooting

If you have issue with flashing via USB OTG, start a new post on the forum. https://forum.radxa.com/c/dev