Please enable javascript, or click here to visit my ecommerce web site powered by Shopify.
Jump to: navigation, search

Difference between revisions of "Rockpi4/dev/usb-install"

< Rockpi4‎ | dev
(Boot the board to maskrom mode)
(Begin Installation USB -> eMMC)
Line 54: Line 54:
 
On your PC, run the rkdeveloptool
 
On your PC, run the rkdeveloptool
  
    rkdeveloptool ld        # List the device
+
rkdeveloptool ld        # List the device
    DevNo=1 Vid=0x2207,Pid=0x330c,LocationID=305 Maskrom
+
DevNo=1 Vid=0x2207,Pid=0x330c,LocationID=305 Maskrom
  
Download the loader (flash helper) to init the ram and prepare the flashing environment etc. If you don't have it, you can download it from [https://dl.radxa.com/rockpi/images/loader/ here]
+
Download the loader (flash helper) to init the ram and prepare the flashing environment etc. If you don't have it, you can download it from [https://dl.radxa.com/rockpi/images/loader/rk3399_loader_v1.20.119.bin here]
  
    rkdeveloptool db rk3399_loader_vxxxx.bin
+
rkdeveloptool db rk3399_loader_v1.20.119.bin
  
 
Write the GPT image to eMMC, start to write from offset '''0'''.
 
Write the GPT image to eMMC, start to write from offset '''0'''.
  
    rkdeveloptool wl 0 /path/to/rockpi4b-xxx-gpt.img
+
rkdeveloptool wl 0 /path/to/rockpi4b-xxx-gpt.img
  
 
Reboot the device
 
Reboot the device
  
    rkdeveloptool rd
+
rkdeveloptool rd
  
Now the device should boot the new image on eMMC
+
Now the device should boot the new image on eMMC.
  
Please notice that when you want to erase eMMC on board, you can use this command. Get zero.img from [https://dl.radxa.com/rockpi4/images/others/zero.img.gz here].
+
Please note that when you want to erase eMMC on board, you can use these commands.
  
    rkdeveloptool db rk3399_loader_vxxxx.bin
+
dd if=/dev/zero of=./zero.img bs=1M count=64
    rkdeveloptool wl 0 zero.img
+
rkdeveloptool db rk3399_loader_v1.20.119.bin
 +
rkdeveloptool wl 0 zero.img
  
 
</div>
 
</div>

Revision as of 07:15, 15 January 2022

    ROCK Pi 4 >  Development >  Install image to eMMC from USB OTG port

Install image to eMMC from USB OTG port

ROCK Pi 4 supports Maskrom mode, which is a special operation mode for CPU to wait for USB OTG port command. The Linux/macOS PC tool we use to communicate with ROCK Pi 4 in Maskrom mode are the rkdeveloptool and RKDevTool. We use tool rkdeveloptool in Linux/macOS and RKDevTool tool under Windows.

Requirement

  • ROCK Pi 4 mainboard
    • ROCK Pi 4A
    • ROCK Pi 4A Plus
    • ROCK Pi 4B
    • ROCK Pi 4B Plus
    • ROCK Pi 4C
  • eMMC on board or eMMC module
  • Power adapter
  • USB Male A to Male A cable(important) USB C to USB A cable does not working on all PCs. See discussion.

Install Tools&Drivers

Please check this guide, Install rockchip flash tools, rkdeveloptool/RKDevTool, under Windows/Linux/MacOS PC.

Boot the board to maskrom mode

To boot ROCK Pi 4 into maskrom mode is simple:

  • 1. Power off the board
  • 2. Short-circuit SPI Nor Flash if there is one SPI Nor Flash on board.

Spi clk gnd.jpg

  • 3. Remove microSD card
  • 4. Insert removable eMMC module ( Skip this when there in one eMMC on board)
  • 5. Plug the USB Male A to Male A cable to ROCK Pi 4 OTG port(the upper USB3 port), the other side to PC
  • 6. Press and hold the Maskrom key if your board is Plus version with soldered eMMC (1: Reset 2: Maskrom 3: Recovery)

Rockpi4bplus key.jpg

  • 7. Power on the board and release the maskrom key(important)
  • 8. Confirm that ROCK Pi 4 is in Maskrom mode .
    • For macOS host: lsusb result: Bus 000 Device 004: ID 2207:330c Fuzhou Rockchip Electronics Co., Ltd. Composite Device
    • For Linux host: lsusb result: Bus 001 Device 112: ID 2207:330c Fuzhou Rockchip Electronics Company
    • For Windows host: Open RKDevTool and you would see the device is in Found One MASKROM Device.

AndroidTool1.PNG

Alternatively, if you are running Android and can access ADB, you can reboot the device to loader mode `adb reboot bootloader` then use the rkdeveloptool to reset the device into maskrom mode `rkdeveloptool rd 3` or Windows AndroidTool Switch button to go to maskrom mode.

Begin Installation USB -> eMMC

Linux/macOS

On your PC, run the rkdeveloptool

rkdeveloptool ld        # List the device
DevNo=1	Vid=0x2207,Pid=0x330c,LocationID=305	Maskrom

Download the loader (flash helper) to init the ram and prepare the flashing environment etc. If you don't have it, you can download it from here

rkdeveloptool db rk3399_loader_v1.20.119.bin

Write the GPT image to eMMC, start to write from offset 0.

rkdeveloptool wl 0 /path/to/rockpi4b-xxx-gpt.img

Reboot the device

rkdeveloptool rd

Now the device should boot the new image on eMMC.

Please note that when you want to erase eMMC on board, you can use these commands.

dd if=/dev/zero of=./zero.img bs=1M count=64
rkdeveloptool db rk3399_loader_v1.20.119.bin
rkdeveloptool wl 0 zero.img

Windows

Double click the RKDevTool.exe and you will see the following interface: If your ROCK Pi 4 is in maskrom mode and connects to PC, you can see that the program detect it, as the red box shown below:

AndroidTool1.PNG

Step 1: Select Loader

Next, click the button in the red box on the right last columns select the loader "rk3399_ loader_ xxxxx.bin ",

AndroidTool8.PNG

Note: the loader (flash helper) is used to init the ram and prepare the flashing environment etc. If you don't have it, you can download it from here

Step 2: Select Image

Then click the right last columns to in the Image row and choose the image you want to flash.

Note: Normally the image name should ends with xxx-gpt.img. If the image name ends with xxx-rkupdate.img, you can not flash with this method.

Step 3: Run

Finally, click the "run" button in the red box below, and you will see the content in the red box on the right. When the progress reaches 100%, the download is completed.

Androidtool5.PNG

Install by partitions(Advanced)

Linux/macOS

Sometimes we only want to update a partition of the image, for example only the boot partition to update kernel only. We can flash by partitions

| Part Number | Offset | Name    | Description                |
| ----------- | ------ | ------- | -------------------------- |
| 1           | 32KB   | loader1 | First stage loader         |
| 2           | 8MB    | loader2 | U-boot image               |
| 3           | 12MB   | trust   | ATF                        |
| 4           | 16MB   | boot    | Kernel partition, bootable |
| 5           | 128MB  | rootfs  | Rootfs                     |

When the board is in maskrom mode, flash the partitions with the following command and offset:

   rkdeveloptool db rk3399_loader_*.bin
   rkdeveloptool wl 64 idbloader.img
   rkdeveloptool wl 16384 uboot.img
   rkdeveloptool wl 24576 trust.img
   rkdeveloptool wl 32768 boot.img
   rkdeveloptool wl 262144 rootfs.img

Windows

TBD.

FAQ

If you meet such these situations, you can try to change the bin file by rk3399_loader_v1.20.119.bin

Error-loader1.png Error-loader2.png

Troubleshooting