ROCK Pi 4 > Development > Build mainline kernel(5.x)
ROCK Pi 4 is officially supported in mainline kernel since v5.1 thanks to developer Akash Gajjar from Mentor. Below is how to build it on a X86 Linux host PC and run on ROCK Pi 4.
- 1 Please help to fix/enhance this page
- 2 Build kernel on linux PC
- 3 Install it on ROCK Pi 4.
Please help to fix/enhance this page
As of 01/07/2020, these instructions are incomplete, incorrect and do not result in a working kernel. Please help to fix them.
Use [] to discuss this page.
- RockPI 4 A with 2GByte
- 16 GByte eMMC module (no uSD)
- Current debian (5.5.0-rc5-00039-gae6088216ce4).
Without any overlays configured, the kernel starts to boot with working console output, but then it seems to hang after the following output:
... [ 14.670351] mmc_host mmc0: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0) [ 14.674934] hctosys: unable to open rtc device (rtc0)
ID of root file system
The instructions show a specific PARTUUID. It seems as if the instructions should explain that the PARTUUID needs to be changed according to the PARTUUID of the boot partition on the boot device - aka: The same PARTUUID used with the 'old' radxa 4.4 kernel ?!
Use of overlays
The instructions on this page do not describe if/how overlays can be used with mainline kernel:
The instructions do not explain if overlays need to be compiled for the new kernel or not.
The instructions do not explain why overlays may fail to work, for example because all or some of the overlays do not have according entry points in the mainline kernel ?
The instructions do not explain if it is possible to configure u-boot so that there are different overlays enabled for different kernels - e.g.: all necessary overlays for the radxa 4.4 kernel and non (or others) for a mainline kernel. Is this even possible ?
Result: When attempting to use ANY overlays such as spi1-flash, the boot process fails to merge the overlays and reverts to boot the first (default) kernel instead.
The console log for this looks as follows:
... reading /rk3399-rock-pi-4.dtb 54207 bytes read in 13 ms (4 MiB/s) fdt addr 0000000008300000 fdt magic number edfe0dd0 fdt size 1048576 merge_dts_overlay Retrieving file: /overlays/spi1-flash.dtbo reading /overlays/spi1-flash.dtbo 765 bytes read in 11 ms (67.4 KiB/s) overlay dtb(0x0000000008200000) is valid fdt_overlay_apply 0000000008300000 0000000008200000 fdt_overlay_apply(): FDT_ERR_NOTFOUND Can't load dts overlay Can not merge dts overlay ERROR: Did not find a cmdline Flattened Device Tree Could not find a valid device tree ...
The kernel will need dynamically loaded modules. These need to be installed into /lib/modules/<kernel-name>.
It is unclear how to best do this when compiling on a separate PC (cross-compilation as explained).
When compiling locally on the Rock PI 4, this is easily achied by using "make modules_install".
Build kernel on linux PC
$ sudo apt-get install libncurses-dev flex bison libssl-dev git
Get the mainline kernel source
$ git clone git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git $ cd linux
Install toolchain from Linaro
$ wget https://releases.linaro.org/components/toolchain/binaries/7.3-2018.05/aarch64-linux-gnu/gcc-linaro-7.3.1-2018.05-x86_64_aarch64-linux-gnu.tar.xz $ sudo tar xvf gcc-linaro-7.3.1-2018.05-x86_64_aarch64-linux-gnu.tar.xz -C /usr/local/ $ export ARCH=arm64 $ export CROSS_COMPILE=/usr/local/gcc-linaro-7.3.1-2018.05-x86_64_aarch64-linux-gnu/bin/aarch64-linux-gnu-
$ make defconfig $ make -j6
Copy arch/arm64/boot/Image and arch/arm64/boot/dts/rk3399-rock-pi-4.dtb to your ROCK Pi 4.
Install it on ROCK Pi 4.
$ sudo cp Image rk3399-rock-pi-4.dtb /boot/
Configure and Reboot
$ sudo vim /boot/extlinux/extlinux.conf
Add an entry as follows:
label kernel-mainline kernel /Image fdt /rk3399-rock-pi-4.dtb append earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1 coherent_pool=1m earlyprintk console=ttyS2,1500000n8 rw root=PARTUUID=b921b045-1d rootfstype=ext4 init=/sbin/init rootwait
Reboot you will have the new kernel booting.
If you have a serial console connected to the Rock PI 4, you can also add this kernel as a second or further boot entry and then select it during the bootstrap process as follows:
... Retrieving file: /extlinux/extlinux.conf reading /extlinux/extlinux.conf 956 bytes read in 17 ms (54.7 KiB/s) select kernel 1: kernel-4.4.154-100-rockchip-gf7c3df9923c2 2: kernel-mainline Enter choice: 2 ... ... 2: kernel-mainline Retrieving file: /Image reading /Image
You need to be fast typing the desired number (2).
The benefit of this approach is that the bootstrap process will automatically revert booting the first (working radxa) kernel when the newly built kernel fails to boot - or that you can simply power cycle to boot the working kernel in case the newly built kernel does not work.