Please enable javascript, or click here to visit my ecommerce web site powered by Shopify.
Jump to: navigation, search

Rock3/CM3/e23

< Rock3‎ | CM3
Revision as of 08:50, 15 January 2022 by Hipboi (Talk | contribs)

    ROCK 3 >  ROCK 3 Compute Module >  Radxa E23 Dual Ethernet Carrier Board

Radxa E23 Dual Ethernet Board is an application board based on the ROCK3 Compute Module(CM3) for networking applications.

Radxa e23 top bottom.jpg

What you need

Necessary

  • Radxa E23
  • One of the Storage media below:
    • microSD, larger than 8GB.
    • eMMC, larger than 8GB.
  • Power supply
    • Radxa E23 is powered by Type-C port. Input voltage is 5V only.
  • USB Male A to Male A cable
    • If you want write image on ROCK 3 from USB OTG port or use fastboot/adb commands you need an USB Male A to Male A cable to connect ROCK 3 and PC.

Optional

  • microSD Card Reader
    • For flashing the image into microSD Card
  • USB to TTL serial cable
    • This is needed for serial console.
  • Ethernet cable
    • Radxa E23 supports Internet access via WIFI or Ethernet.
    • An Ethernet cable is used to connect your Radxa E23 to a local network and the Internet.
  • Audio cable
    • Audio can be played through speaker or headphones using a standard 3.5mm jack.

Features

Model Radxa E23
SoC

CPU
GPU
NPU
RK3566

Quad-core Cortex-A55, freqency 2Ghz

Mali G52
0.8TOPS NPU

Memory 1GB, 2GB, 4GB or 8GB LPDDR4 (depending on SoM variant)
Storage eMMC (8/16/32/64/128GB)
μSD card (μSD slot supports up to 128 GB μSD card)
one SPI Nor Flash
one EEPROM
Audio 3.5mm jack with mic
HD codec that supports up to 24-bit/96KHz audio.
Wireless Optional wireless LAN, 2.4GHz and 5.0GHz IEEE 802.11b/g/n/ac wireless.
Bluetooth 5.0, BLE with external antenna (depending on SoM variant).
USB USB 3.0 HOST X1
USB 2.0 OTG X1(USB C)
USB 2.0 HOST(40P GPIO)
Ethernet 1GbE LAN X1
2.5GbE LAN X1(PoE Support)
IO 40-pin expansion header
LED Green LED X1
RGB LED X1
Key Power Key X1
Recovery Key X1
Power USB Type-C DC 5V
Size 2.5x2.2 inch(56x65mm)

Resource

Power supply

Radxa E23 is powered by Type-C port with 5V input, you can power it from 5V USB adapter or from PC/Laptop USB port.

eMMC

Radxa E23 is equipped with different capacities of eMMC (8/16/32/64/128GB). See Radxa CM3 Models and SKU.

DDR

Radxa E23 is equipped with different capacities of DDR (1//2/4/8GB). See Radxa CM3 Models and SKU.

Wireless module

With Wireless variant SoM, Radxa E23 have WiFi 2.4G&5G and Bluetooth 5.0 capability. To gain a stronger signal, you need an antenna attached to the antenna socket on board. The u.FL connector type is IPEX Gen 1.

Ethernet

Radxa E23 has one 1GbE LAN port and one 2.5GbE LAN port.

1GbE LAN port LED status and speed table.

LED speed
Yellow 1000M
Green 100M

Type-A USB 3.0

The Type-A USB 3.0 port enables the attachment of peripherals such U Disk, keyboards, mice, USB dongle etc.

USB 2.0 OTG

USB 2.0 OTG can be accessed from the USB C port together with the power in. When powering from PC/laptop, the host can communicate with the board via USB protocol such as ADB, USB networking etc.

USB 2.0 HOST

Radxa E23 40-pin Header USB Interface
PIN#18 Data+
PIN#16 Data-
PIN#14 GND
PIN#2 5V

TF/MicroSD

The TF card can be used as a system storage or an external storage. When it's used as a system storage, you had better choose the ones with storage space larger than 8GB. When it's used as an external storage, you can choose the ones with storage space up to 128GB. When the TF card is inserted into the TF card slot , the device will be automatically recognized by the system.

The TF card interface pin specification shows below.

Pin# Name
1 SDMMC0_D2
2 SDMMC0_D3
3 SDMMC0_CMD
4 VCC3V3_SYS
5 SDMMC0_CLK
6 GND
7 SDMMC0_D0
8 SDMMC0_D1
9 SDMMC0_DET_L
10 GND
11 GND
12 GND
13 GND

Audio: 3.5mm jack with MIC

Audio can be played through speaker or headphones using a standard 3.5mm jack with MIC.

Note that HD codec supports up to 24-bit/96KHz audio.

LED

One Green Flashing LED is on Radxa CM3 for kernel status.

One RGB LED is controlled by three PWM channels. They can be controlled under Linux via sysfs. Below is their related sysfs directories.

RGB LED --- sysfs
Red --- /sys/devices/platform/fdd70000.pwm/pwm/pwmchip*/
Green --- /sys/devices/platform/fdd70030.pwm/pwm/pwmchip*/
Blue --- /sys/devices/platform/fe6f0030.pwm/pwm/pwmchip*/

Key

There are two keys on board. One is power key and the other one is recovery key.

Key Function
Power key Power on/off Radxa E23
Recovery key Boot Radxa E23 to loader mode:
* Press recovery key and hold it
* Plug in Type-C adapter
* Wait for 5 seconds
* Release recovery key

General purpose input-output (GPIO) connector

Check E23 GPIO

System images and usage

Get your favorite system images from Radxa E23 Downloads.

And check the features of Ubuntu or Debian.

Flash images

Radxa E23 supports two boot methods including booting from eMMC and booting from MicroSD. Select one of the following methods.

Troubleshooting

Check ROCK 3 FAQs first, if it doesn't help, start a new post on the forum https://forum.radxa.com/c/rock3.