Please enable javascript, or click here to visit my ecommerce web site powered by Shopify.
Jump to: navigation, search

Penta SATA HAT

Revision as of 07:01, 23 July 2020 by Setq (Talk | contribs)


    Home >  SATA HAT >  Penta SATA HAT


Introduction

Penta sata hat angle.png

ROCK Pi Penta SATA HAT is an addon HAT designed for ROCK Pi 4. It utilizes the high speed PCIe buses on ROCK Pi 4 and providing a complete NAS solution based on ROCK Pi 4. It has the following features:

  • Up to 5x HDD/SSD, support 2.5inch or 3.5inch SSD, up to 100T Storage
  • 4x SATA + 1x eSATA with power
  • Utilize two lanes PCIe 2.1 buses on ROCK Pi 4
  • External standard ATX power supply support for HDD and ROCK Pi 4
  • 12V DC power input for 2.5/3.5 HDD power and ROCK Pi 4
  • Support HDD suspend mode
  • Support software RAID 0/1/5
  • Optional PWM control fan for HDD heat dispatching
  • Optional OLED display for IP/Storage info

Software support

We provide a install script to help you get the Penta SATA software that works in ROCK Pi 4.

curl -sL https://rock.sh/get-rockpi-penta | sudo -E bash -

Just copy the command above and paste it into the terminal and press enter. If you want more settings, check out section Software Configuration at the bottom of the page.

In particular, users of Armbian, please use the installation script below:

curl -sL https://rock.sh/get-penta-armbian | sudo -E bash -

Supplied with this product

  • Penta SATA HAT
  • Mechanical spacers
  • M.2 to FPC board and high speed FPC cable
  • eSATA to SATA 7+15P cable with power

SATA HAT top board(Optional)

  • 0.91inch OLED
  • One GPIO button
  • PWM controlled 40x40mm FAN
  • Cable for SATA HAT to top board

Sata hat top board.png

Metal Case(Optional)

  • Holds up to four 2.5 inch HDDs/SSDs
  • Bottom big heatsink for ROCK Pi 4 CPU
  • Supports top board
  • Top acrylic cover for OLED display
  • One button for powering off and OLED info switch
  • eSATA connector exported
  • Support fan for HDD heat dispatching air flow

Quad sata case coke.jpeg

Other hardware needed

  • Proper power adapter(Check power options below for more info)
  • 2.5inch or 3.5inch HDD/SSD
  • ROCK Pi 4 with os running
  • optional 7+15P SATA cable(For 3.5inch HDD or extending the length)

Model Number

The Penta SATA HAT is designed for ROCK Pi 4, one model only.

Model Description
PF4 Support four 2.5/3.5inch HDD/SSD plus one eSATA

Getting Started

Power Options

Power consumptions for typical disks:

Power Consumption
SSD <3W
2.5 HDD 3 ~ 5W
2.5 HDD 5 ~10W

Note: the table above is for reference, check your disk label for the exact power consumption. More info can be found here.

Option 1: Powering from ROCK Pi 40P GPIO header

The ROCK Pi 4 GPIO +5V can provide up to 4A current. You can drive four SSD/HDD directly if your power adapter can provide > 35W power.

Option 2: Powering from 12V DC Jack on SATA HAT

For Penta SATA HAT, we use 12V DC power jack on SATA HAT since 12V power adapter is much cheaper than USB C PD adapter. Also, users want to power 3.5inch HDD with power adapter instead of ATX PSU. The 12V DC jack is 5.5x2.1mm diameter. You need at least 12V/4A to power four 2.5inch HDD plus eSATA and 12V/6A to power four 3.5inch HDD plus eSATA.

Option 3: Power from ATX PSU

If you plan to put the SATA HAT in a PC enclosure, then you can use the ATX PSU. Mostly ATX PSU can meet the power requirement. You need a ATX 4P HDD power cable to power the SATA HAT and ROCK Pi 4.

Software configuration

Just edit /etc/rockpi-penta.conf, take it effect by below command

sudo systemctl restart rockpi-penta.service

Below is the default /etc/rockpi-penta.conf, which you can modify according to the comments

  1. [fan]
  2. # When the temperature is above lv0 (35'C), the fan at 25% power,
  3. # and lv1 at 50% power, lv2 at 75% power, lv3 at 100% power.
  4. # When the temperature is below lv0, the fan is turned off.
  5. # You can change these values if necessary.
  6. lv0 = 35
  7. lv1 = 40
  8. lv2 = 45
  9. lv3 = 50
  10.  
  11. [key]
  12. # You can customize the function of the key, currently available functions are
  13. # slider: oled display next page
  14. # switch: fan turn on/off switch
  15. # reboot, poweroff
  16. # If you have any good suggestions for key functions, 
  17. # please add an issue on https://rock.sh/rockpi-sata
  18. click = slider
  19. twice = switch
  20. press = none
  21.  
  22. [time]
  23. # twice: maximum time between double clicking (seconds)
  24. # press: long press time (seconds)
  25. twice = 0.7
  26. press = 1.8
  27.  
  28. [slider]
  29. # Whether the oled auto display next page and the time interval (seconds)
  30. auto = true
  31. time = 10
  32.  
  33. [oled]
  34. # Whether rotate the text of oled 180 degrees, whether use Fahrenheit
  35. rotate = false
  36. f-temp = false

Dimensions