Penta SATA HAT

English

    Home >  SATA HAT >  Penta SATA HAT

Introduction

ROCK Pi Penta SATA HAT is an addon HAT designed for ROCK Pi 4. It utilizes the high speed PCIe buses on ROCK Pi 4 and providing a complete NAS solution based on ROCK Pi 4. It has the following features:

Up to 5x HDD/SSD, support 2.5inch or 3.5inch SSD, up to 100T Storage
4x SATA + 1x eSATA with power
Utilize two lanes PCIe 2.1 buses on ROCK Pi 4
External standard ATX power supply support for HDD and ROCK Pi 4
12V DC power input for 2.5/3.5 HDD power and ROCK Pi 4
Support HDD suspend mode
Support software RAID 0/1/5
Optional PWM control fan for HDD heat dispatching
Optional OLED display for IP/Storage info

Software support

We provide a install script to help you get the Penta SATA software that works in ROCK Pi 4.

curl -sL https://rock.sh/get-rockpi-penta | sudo -E bash -

Just copy the command above and paste it into the terminal and press enter. If you want more settings, check out section Software Configuration at the bottom of the page.

In particular, users of Armbian, please use the installation script below:

curl -sL https://rock.sh/get-penta-armbian | sudo -E bash -

Supplied with this product

Penta SATA HAT
Mechanical spacers
M.2 to FPC board and high speed FPC cable
eSATA to SATA 7+15P cable with power

SATA HAT top board(Optional)

0.91inch OLED
One GPIO button
PWM controlled 40x40mm FAN
Cable for SATA HAT to top board

Metal Case(Optional)

Holds up to four 2.5 inch HDDs/SSDs
Bottom big heatsink for ROCK Pi 4 CPU
Supports top board
Top acrylic cover for OLED display
One button for powering off and OLED info switch
eSATA connector exported
Support fan for HDD heat dispatching air flow

5 Bay 3.5HDD case (Optional)

5 bay pluggable 3.5inch HDD case

Other hardware needed

Proper power adapter(Check power options below for more info)
2.5inch or 3.5inch HDD/SSD
ROCK Pi 4 with os running
optional 7+15P SATA cable(For 3.5inch HDD or extending the length)

Model Number

The Penta SATA HAT is designed for ROCK Pi 4, one model only.

Model	Description
PF4	Support four 2.5/3.5inch HDD/SSD plus one eSATA

Getting Started

Power Options

Power consumptions for typical disks:

	Power Consumption
SSD	<3W
2.5 HDD	3 ~ 5W
2.5 HDD	5 ~10W

Note: the table above is for reference, check your disk label for the exact power consumption. More info can be found here.

Option 1: Powering from ROCK Pi 40P GPIO header

The ROCK Pi 4 GPIO +5V can provide up to 4A current. You can drive four SSD/HDD directly if your power adapter can provide > 35W power.

Option 2: Powering from 12V DC Jack on SATA HAT

For Penta SATA HAT, we use 12V DC power jack on SATA HAT since 12V power adapter is much cheaper than USB C PD adapter. Also, users want to power 3.5inch HDD with power adapter instead of ATX PSU. The 12V DC jack is 5.5x2.1mm diameter. You need at least 12V/4A to power four 2.5inch HDD plus eSATA and 12V/6A to power four 3.5inch HDD plus eSATA.

Option 3: Power from ATX PSU

If you plan to put the SATA HAT in a PC enclosure, then you can use the ATX PSU. Mostly ATX PSU can meet the power requirement. You need a ATX 4P HDD power cable to power the SATA HAT and ROCK Pi 4.

Software configuration

Just edit /etc/rockpi-penta.conf, take it effect by below command

sudo systemctl restart rockpi-penta.service

Below is the default /etc/rockpi-penta.conf, which you can modify according to the comments

```
[fan]
```

# When the temperature is above lv0 (35'C), the fan at 25% power,

# and lv1 at 50% power, lv2 at 75% power, lv3 at 100% power.

# When the temperature is below lv0, the fan is turned off.

# You can change these values if necessary.

```
lv0 = 35
```
```
lv1 = 40
```
```
lv2 = 45
```
```
lv3 = 50
```
```
 
```
```
[key]
```

# You can customize the function of the key, currently available functions are

```
# slider: oled display next page
```
```
# switch: fan turn on/off switch
```
```
# reboot, poweroff
```

# If you have any good suggestions for key functions,

# please add an issue on https://rock.sh/rockpi-sata

```
click = slider
```
```
twice = switch
```
```
press = none
```
```
 
```
```
[time]
```

# twice: maximum time between double clicking (seconds)

```
# press: long press time (seconds)
```
```
twice = 0.7
```
```
press = 1.8
```
```
 
```
```
[slider]
```

# Whether the oled auto display next page and the time interval (seconds)

```
auto = true
```
```
time = 10
```
```
 
```
```
[oled]
```

# Whether rotate the text of oled 180 degrees, whether use Fahrenheit

```
rotate = false
```
```
f-temp = false
```