Difference between revisions of "Penta SATA HAT"
RadxaYuntian (Talk | contribs) |
|||
| Line 261: | Line 261: | ||
| style="text-align: center;" | 7 | | style="text-align: center;" | 7 | ||
| style="text-align: center;" | 8 | | style="text-align: center;" | 8 | ||
| − | | style="text-align: center;" | PWM_33 | + | | style="text-align: center;" | GPIO4_C6(can be hardware modified to use PWM_33) |
|- | |- | ||
| style="text-align: center;" | GND | | style="text-align: center;" | GND | ||
| Line 273: | Line 273: | ||
==== Power Options ==== | ==== Power Options ==== | ||
| − | Power | + | Power consumption for typical disks: |
{| class="wikitable" | {| class="wikitable" | ||
Revision as of 03:42, 28 January 2023
Home > SATA HAT > Penta SATA HAT
Introduction
ROCK Pi Penta SATA HAT is an addon HAT designed for ROCK Pi 4. It utilizes the high-speed PCIe buses on ROCK Pi 4 and provides a complete NAS solution based on ROCK Pi 4. It has the following features:
- Up to 5x HDD/SSD, support 2.5inch or 3.5inch SSD, up to 100T Storage
- 4x SATA + 1x eSATA with power
- Utilize two lanes PCIe 2.1 buses on ROCK Pi 4
- External standard ATX power supply support for HDD and ROCK Pi 4
- 12V DC power input for 2.5/3.5 HDD power and ROCK Pi 4
- Support HDD suspend mode
- Support software RAID 0/1/5
- Optional PWM control fan for HDD heat dispatching
- Optional OLED display for IP/Storage info
Software support
We provide an install script to help you get the Penta SATA software that works in ROCK Pi 4.
curl -sL https://rock.sh/get-rockpi-penta | sudo -E bash -
Just copy the command above and paste it into the terminal and press enter. If you want more settings, check out section Software Configuration at the bottom of the page.
Supplied with this product
- Penta SATA HAT
- Mechanical spacers
- M.2 to FPC board and high-speed FPC cable
SATA HAT top board(Optional)
- 0.91inch OLED
- One GPIO button
- PWM controlled 40x40mm FAN
- Cable for SATA HAT to top board
Metal Case(Optional)
- Holds up to four 2.5-inch HDDs/SSDs
- Bottom big heatsink for ROCK Pi 4 CPU
- Supports top board
- Top acrylic cover for OLED display
- One button for powering off and OLED info switch
- eSATA connector exported
- Support fan for HDD heat dispatching airflow
5 Bay 3.5HDD case (Optional)
- 5 bay pluggable 3.5inch HDD case
Other hardware needed
- Proper power adapter(Check power options below for more info)
- 2.5inch or 3.5inch HDD/SSD
- ROCK Pi 4 with os running
- optional 7+15P SATA cable(For 3.5inch HDD or extending the length)
Model Number
The Penta SATA HAT is designed for ROCK Pi 4, one model only.
| Model | Description |
|---|---|
| PF4 | Support four 2.5/3.5inch HDD/SSD plus one eSATA |
PINOUT
Pinout for 40PIN GPIO header
| Description | Function | Pin# | Pin# | Function | Description | |
|---|---|---|---|---|---|---|
| 1 | 2 | VCC5V0_SYS | ||||
| OLED I2C | I2C_SDA | 3 | 4 | VCC5V0_SYS | ||
| OLED I2C | I2C_SCL | 5 | 6 | |||
| 7 | 8 | |||||
| 9 | 10 | |||||
| top board key | GPIO4_C2 | 11 | 12 | |||
| GPIO4_C6 | 13 | 14 | ||||
| 15 | 16 | GPIO4_D2 | reset OLED | |||
| 17 | 18 | |||||
| 19 | 20 | |||||
| 21 | 22 | |||||
| 23 | 24 | |||||
| 25 | 26 | ADC_IN0 | temperature | |||
| SDA | 27 | 28 | SCL | |||
| 29 | 30 | |||||
| 31 | 32 | |||||
| control tb-fan speed | PWM_33 | 33 | 34 | |||
| 35 | 36 | |||||
| 37 | 38 | |||||
| 39 | 40 |
Pinout for 2x5 PHD 2.0mm connector
| Function | Pin# | Pin# | Function | |
|---|---|---|---|---|
| I2C_SDA | 1 | 2 | VCC3V3_SYS | |
| I2C_SCL | 3 | 4 | VCC5V0_SYS | |
| GPIO4_D2 | 5 | 6 | GPIO4_C2 | |
| GND | 7 | 8 | GPIO4_C6(can be hardware modified to use PWM_33) | |
| GND | 9 | 10 | NC |
Getting Started
Power Options
Power consumption for typical disks:
| Power Consumption | |
|---|---|
| SSD | <3W |
| 2.5 HDD | 3 ~ 5W |
| 3.5 HDD | 5 ~10W |
Note: the table above is for reference, check your disk label for the exact power consumption. More info can be found here.
Option 1: Powering from ROCK Pi 40P GPIO header
The ROCK Pi 4 GPIO +5V can provide up to 4A current. You can drive four SSD/HDD directly if your power adapter can provide > 35W power.
Option 2: Powering from 12V DC Jack on SATA HAT
For Penta SATA HAT, we use a 12V DC power jack on SATA HAT since the 12V power adapter is much cheaper than a USB C PD adapter. Also, users want to power a 3.5inch HDD with a power adapter instead of an ATX PSU. The 12V DC jack is 5.5x2.5mm in diameter. You need at least 12V/4A to power four 2.5inch HDD plus eSATA and 12V/6A to power four 3.5inch HDD plus eSATA.
Option 3: Power from ATX PSU
If you plan to put the SATA HAT in a PC enclosure, then you can use the ATX PSU. Mostly ATX PSU can meet the power requirement. You need an ATX 4P HDD power cable to power the SATA HAT and ROCK Pi 4.
Software configuration
Just edit /etc/rockpi-penta.conf, take it effect by below command
sudo systemctl restart rockpi-penta.service
Below is the default /etc/rockpi-penta.conf, which you can modify according to the comments
[fan]# When the temperature is above lv0 (35'C), the fan at 25% power,
# and lv1 at 50% power, lv2 at 75% power, and lv3 at 100% power.
# When the temperature is below lv0, the fan is turned off.
# You can change these values if necessary.
lv0 = 35
lv1 = 40
lv2 = 45
lv3 = 50
[key]# You can customize the function of the key, currently available functions are
# slider: oled display next page
# switch: fan turn on/off switch
# reboot, poweroff
# If you have any good suggestions for key functions,
# please add an issue on https://rock.sh/rockpi-sata
click = slider
twice = switch
press = none
[time]# twice: maximum time between double clicking (seconds)
# press: long press time (seconds)
twice = 0.7
press = 1.8
[slider]# Whether the oled auto display next page and the time interval (seconds)
auto = true
time = 10
[oled]# Whether rotate the text of oled 180 degrees, whether use Fahrenheitrotate = false
f-temp = false