Difference between revisions of "ROCKPI 23W PoE HAT"
RadxaYuntian (Talk | contribs) (→Model) |
|||
| (9 intermediate revisions by 2 users not shown) | |||
| Line 2: | Line 2: | ||
__NOTOC__ | __NOTOC__ | ||
| − | [[home | Home]] > [[ROCKPI_23W_PoE_HAT | ROCK Pi 23W PoE HAT]] | + | [[home | Home]] > [[PoE_HAT |PoE HAT]] > [[ROCKPI_23W_PoE_HAT | ROCK Pi 23W PoE HAT]] |
=== Introduction === | === Introduction === | ||
| Line 8: | Line 8: | ||
[[File:Rockpi_with_poe_hat.png | 400px |right]] | [[File:Rockpi_with_poe_hat.png | 400px |right]] | ||
| − | ROCK Pi 23W PoE HAT is a HAT | + | ROCK Pi 23W PoE HAT is a HAT accessory designed for Raspberry Pi, ROCK Pi 4, and Jetson Nano. The 23W PoE HAT allows you to power your Raspberry Pi, ROCK Pi 4 or Jetson Nano using Power over Ethernet–enabled networks; for this product to be used, the network it is connected to needs to have power-sourcing equipment installed. |
It comes with the following features: | It comes with the following features: | ||
| Line 19: | Line 19: | ||
* Clean design by hiding the fan and the big transformer inside | * Clean design by hiding the fan and the big transformer inside | ||
* EEPROM for HAT identity and driver probe | * EEPROM for HAT identity and driver probe | ||
| − | |||
| − | |||
=== Supplied with this product === | === Supplied with this product === | ||
| Line 26: | Line 24: | ||
* Mechanical spacers | * Mechanical spacers | ||
=== Other hardware needed === | === Other hardware needed === | ||
| − | * A Raspberry Pi 4 Model B or Raspberry Pi 3 Model B+ or ROCK Pi 4 | + | * A Raspberry Pi 4 Model B or Raspberry Pi 3 Model B+ or ROCK Pi 4 or Jetson Nano |
* An Ethernet cable | * An Ethernet cable | ||
| − | * Power-sourcing equipment for | + | * Power-sourcing equipment for an 802.3af or 802.3at Power over Ethernet network |
=== Software support === | === Software support === | ||
| − | We provide | + | We provide an install script to help you get the PoE fan control tool that works both in '''Raspberry Pi 3B+/4B''' and '''ROCK Pi 4'''. |
| + | |||
| + | [[File:Get-23w-poe.png]] | ||
curl -sL https://rock.sh/get-rockpi-poe | sudo -E bash - | curl -sL https://rock.sh/get-rockpi-poe | sudo -E bash - | ||
| Line 46: | Line 46: | ||
|- | |- | ||
| F3 | | F3 | ||
| − | | For Raspberry Pi 3B+, Raspberry Pi 4, Jetson Nano | + | | For Raspberry Pi 3B+, Raspberry Pi 4, '''ROCK Pi X''', '''ROCK 3A''', ROCK 3C, ROCK Pi 4C+, Jetson Nano |
|- | |- | ||
| F3L | | F3L | ||
| Line 52: | Line 52: | ||
|- | |- | ||
| F4 | | F4 | ||
| − | | Use with ROCK Pi | + | | Use with ROCK Pi 4B / 4B+ / 4SE |
|- | |- | ||
| F4L | | F4L | ||
| Line 58: | Line 58: | ||
|} | |} | ||
| − | The difference between F3 and F4 is, F3 and F4 | + | The difference between F3 and F4 is, F3 and F4 use different GPIO for fan control. F4 uses ADC for temperature detection, while F3 uses DS18B20. |
=== PINOUT === | === PINOUT === | ||
| Line 108: | Line 108: | ||
|} | |} | ||
| − | ==== PoE HAT for Raspberry Pi 3B+/4 (Model F3/F3L) ==== | + | ==== PoE HAT for Raspberry Pi 3B+/4/Jetson Nano (Model F3/F3L) ==== |
{| class="wikitable" | {| class="wikitable" | ||
| Line 161: | Line 161: | ||
sudo systemctl stop rockpi-poe.service | sudo systemctl stop rockpi-poe.service | ||
| − | Edit /etc/rockpi-poe.conf to set up temperature of the fan speed level, take it effect by below command | + | Edit /etc/rockpi-poe.conf to set up the temperature of the fan speed level, take it to effect by below command |
sudo systemctl restart rockpi-poe.service | sudo systemctl restart rockpi-poe.service | ||
| Line 167: | Line 167: | ||
=== Manual installation === | === Manual installation === | ||
| − | If you have trouble installing software using our script, try manual installation. | + | If you have trouble installing software using our script, try the manual installation. |
'''1. Enable hardware resources''' | '''1. Enable hardware resources''' | ||
| Line 175: | Line 175: | ||
1.1 ROCK Pi | 1.1 ROCK Pi | ||
| − | If you are using the official system, please edit /boot/hw_intfc.conf to change intfc:pwm0=off and intfc:pwm1=off into intfc:pwm0=on and intfc:pwm1=on. If you are using | + | If you are using the official system, please edit /boot/hw_intfc.conf to change intfc:pwm0=off and intfc:pwm1=off into intfc:pwm0=on and intfc:pwm1=on. If you are using another system, please refer to the distribution documentation to open PWM0 and PWM1. |
1.2 Raspberry Pi | 1.2 Raspberry Pi | ||
| − | If you are using Raspbian, you can open '''1-Wire''' with raspi-config and the path is '''Interfacing Options''' -> '''1-Wire'''. Raspbian turns on PWM1 by default. If you are using | + | If you are using Raspbian, you can open '''1-Wire''' with raspi-config and the path is '''Interfacing Options''' -> '''1-Wire'''. Raspbian turns on PWM1 by default. If you are using another system, please refer to the distribution documentation to open 1-Wire and PWM1. |
'''2. Install GPIO control library''' | '''2. Install GPIO control library''' | ||
| Line 185: | Line 185: | ||
2.1 ROCKP Pi | 2.1 ROCKP Pi | ||
| − | If you are using the official system, please install '''libmraa-rockpi4''' from testing repo of [https://wiki.radxa.com/Rockpi4/radxa-apt Radxa APT]. If you are using | + | If you are using the official system, please install '''libmraa-rockpi4''' from testing repo of [https://wiki.radxa.com/Rockpi4/radxa-apt Radxa APT]. If you are using another system, please download [https://github.com/intel-iot-devkit/mraa mraa] and build. |
2.2 ROCKP Pi | 2.2 ROCKP Pi | ||
| − | If you are using Raspbian, you can install python3-rpi.gpio via apt. If you are using | + | If you are using Raspbian, you can install python3-rpi.gpio via apt. If you are using another system, please download [https://sourceforge.net/projects/raspberry-gpio-python raspberry-gpio-python] and build. |
'''3. Download package and install''' | '''3. Download package and install''' | ||
| Line 197: | Line 197: | ||
wget https://cos.setq.me/rockpi/deb/rockpi-poe-0.13.deb | wget https://cos.setq.me/rockpi/deb/rockpi-poe-0.13.deb | ||
| − | If you are using a debian based system, you can install it through dpkg. If you are using | + | If you are using a debian based system, you can install it through dpkg. If you are using another system, extract the file to the root directory. |
3.2 Raspberry Pi | 3.2 Raspberry Pi | ||
| Line 203: | Line 203: | ||
wget https://cos.setq.me/rockpi/deb/raspi-poe-0.13.deb | wget https://cos.setq.me/rockpi/deb/raspi-poe-0.13.deb | ||
| − | If you are using a debian based system, you can install it through dpkg. If you are using | + | If you are using a debian based system, you can install it through dpkg. If you are using another system, extract the file to the root directory. |
'''4. Enable service''' | '''4. Enable service''' | ||
Latest revision as of 02:09, 28 September 2023
Home > PoE HAT > ROCK Pi 23W PoE HAT
Introduction
ROCK Pi 23W PoE HAT is a HAT accessory designed for Raspberry Pi, ROCK Pi 4, and Jetson Nano. The 23W PoE HAT allows you to power your Raspberry Pi, ROCK Pi 4 or Jetson Nano using Power over Ethernet–enabled networks; for this product to be used, the network it is connected to needs to have power-sourcing equipment installed.
It comes with the following features:
- 802.3at up to 23W(5V/4.6A)
- PWM control FAN up to 12000RPM
- Temperature sensor DS18B20
- Optional 40PIN GPIO pass-through exported
- Compatible with ROCK Pi 4, Raspberry Pi 3B+ and Raspberry Pi 4
- Clean design by hiding the fan and the big transformer inside
- EEPROM for HAT identity and driver probe
Supplied with this product
- ROCK Pi 23W PoE HAT
- Mechanical spacers
Other hardware needed
- A Raspberry Pi 4 Model B or Raspberry Pi 3 Model B+ or ROCK Pi 4 or Jetson Nano
- An Ethernet cable
- Power-sourcing equipment for an 802.3af or 802.3at Power over Ethernet network
Software support
We provide an install script to help you get the PoE fan control tool that works both in Raspberry Pi 3B+/4B and ROCK Pi 4.
curl -sL https://rock.sh/get-rockpi-poe | sudo -E bash -
Just copy the command above and paste it into the terminal and press enter. If you want more control, check out section Fan Control at the bottom of the page.
Model
| Model | Description |
|---|---|
| F3 | For Raspberry Pi 3B+, Raspberry Pi 4, ROCK Pi X, ROCK 3A, ROCK 3C, ROCK Pi 4C+, Jetson Nano |
| F3L | F3 with 40PIN GPIO pass-through exported |
| F4 | Use with ROCK Pi 4B / 4B+ / 4SE |
| F4L | F4 with 40PIN GPIO pass-through exported |
The difference between F3 and F4 is, F3 and F4 use different GPIO for fan control. F4 uses ADC for temperature detection, while F3 uses DS18B20.
PINOUT
PoE HAT for ROCK Pi 4(Model F4/F4L)
| Description | Function | Pin# | Pin# | Function | Description | |
|---|---|---|---|---|---|---|
| 1 | 2 | |||||
| 3 | 4 | |||||
| 5 | 6 | |||||
| GPIO2_B3 | 7 | 8 | ||||
| 9 | 10 | |||||
| 11 | 12 | |||||
| control fan speed | PWM1 | 13 | 14 | |||
| GPIO4_C5 | 15 | 16 | GPIO4_D2 | enable/disable fan motor driver | ||
| 17 | 18 | |||||
| 19 | 20 | |||||
| 21 | 22 | |||||
| 23 | 24 | |||||
| 25 | 26 | ADC_IN0 | Get ADC value to get the temperature value | |||
| connect to EEPROM SDA pin | I2C2_SDA | 27 | 28 | I2C2_SCL | connect to EEPROM SCL pin | |
| 29 | 30 | |||||
| 31 | 32 | |||||
| 33 | 34 | |||||
| 35 | 36 | |||||
| 37 | 38 | |||||
| 39 | 40 |
PoE HAT for Raspberry Pi 3B+/4/Jetson Nano (Model F3/F3L)
| Description | Function | Pin# | Pin# | Function | Description | |
|---|---|---|---|---|---|---|
| 1 | 2 | |||||
| 3 | 4 | |||||
| 5 | 6 | |||||
| get data from DS18B20 | BCM4 | 7 | 8 | |||
| 9 | 10 | |||||
| 11 | 12 | |||||
| 13 | 14 | |||||
| enable/disable fan motor driver chip | BCM22 | 15 | 16 | |||
| 17 | 18 | |||||
| 19 | 20 | |||||
| 21 | 22 | |||||
| 23 | 24 | |||||
| 25 | 26 | |||||
| connect to EEPROM SDA pin | I2C0_SDA | 27 | 28 | I2C0_SCL | connect to EEPROM SDA pin | |
| 29 | 30 | |||||
| 31 | 32 | |||||
| control fan speed | PWM1 | 33 | 34 | |||
| 35 | 36 | |||||
| 37 | 38 | |||||
| 39 | 40 |
Fan Control
Turn the fan on or off by systemctl
sudo systemctl start rockpi-poe.service sudo systemctl stop rockpi-poe.service
Edit /etc/rockpi-poe.conf to set up the temperature of the fan speed level, take it to effect by below command
sudo systemctl restart rockpi-poe.service
Manual installation
If you have trouble installing software using our script, try the manual installation.
1. Enable hardware resources
For speed control and temperature detection, we need to ensure that some hardware resources are available, such as PWM and ADC. Since ROCK Pi and Raspberry Pi use different resources, they will be explained below.
1.1 ROCK Pi
If you are using the official system, please edit /boot/hw_intfc.conf to change intfc:pwm0=off and intfc:pwm1=off into intfc:pwm0=on and intfc:pwm1=on. If you are using another system, please refer to the distribution documentation to open PWM0 and PWM1.
1.2 Raspberry Pi
If you are using Raspbian, you can open 1-Wire with raspi-config and the path is Interfacing Options -> 1-Wire. Raspbian turns on PWM1 by default. If you are using another system, please refer to the distribution documentation to open 1-Wire and PWM1.
2. Install GPIO control library
2.1 ROCKP Pi
If you are using the official system, please install libmraa-rockpi4 from testing repo of Radxa APT. If you are using another system, please download mraa and build.
2.2 ROCKP Pi
If you are using Raspbian, you can install python3-rpi.gpio via apt. If you are using another system, please download raspberry-gpio-python and build.
3. Download package and install
3.1 ROCK Pi
wget https://cos.setq.me/rockpi/deb/rockpi-poe-0.13.deb
If you are using a debian based system, you can install it through dpkg. If you are using another system, extract the file to the root directory.
3.2 Raspberry Pi
wget https://cos.setq.me/rockpi/deb/raspi-poe-0.13.deb
If you are using a debian based system, you can install it through dpkg. If you are using another system, extract the file to the root directory.
4. Enable service
sudo systemctl enable rockpi-poe.service
That's all the installation script (https://rock.sh/get-rockpi-poe) do.