RockpiS/getting started/troubleshooting - Revision history

Stephen: /* Check the serial console */

2020-06-01T02:49:36Z

‎Check the serial console

Hipboi: /* Check the serial console */

2019-11-11T04:53:16Z

‎Check the serial console

Stephen: /* Using SSH */

2019-10-29T11:37:51Z

‎Using SSH

Stephen: /* Using SSH */

2019-07-05T10:57:21Z

‎Using SSH

Stephen: /* Using ssh */

2019-07-05T10:56:38Z

‎Using ssh

Stephen at 10:53, 5 July 2019

2019-07-05T10:53:12Z

Stephen: Created page with "{{rockpiS_header}} {{Languages|rockpiS/getting_started/troubleshooting}} ROCK Pi S > Getting Started > rockpiS/getting_start..."

2019-06-25T02:50:36Z

Created page with "{{rockpiS_header}} {{Languages|rockpiS/getting_started/troubleshooting}} ROCK Pi S > Getting Started > rockpiS/getting_start..."

New page

{{rockpiS_header}}
{{Languages|rockpiS/getting_started/troubleshooting}}

[[rockpiS | ROCK Pi S]] > [[rockpiS/getting_started | Getting Started]] > [[rockpiS/getting_started/troubleshooting | Troubleshooting]]

=== Check the serial console ===

By default, the ROCK Pi S uses the colorful 26PIN GPIO header PIN19 and PIN21.

@@ Line 6: / Line 6: @@
 === Check the serial console ===
-. By default, the ROCK Pi S uses the colorful 26PIN GPIO header PIN19 and PIN21.
+. By default, the ROCK Pi S uses the colorful 26PIN GPIO header PIN8 and PIN10.
 . The USB to TTL chip must support 1.5Mbps baud rate, some cheap USB to TTL chip can not support such high baud rate.

@@ Line 6: / Line 6: @@
 === Check the serial console ===
-By default, the ROCK Pi S uses the colorful 26PIN GPIO header PIN19 and PIN21.
+. By default, the ROCK Pi S uses the colorful 26PIN GPIO header PIN19 and PIN21.
 === Default non-root user  ===

@@ Line 19: / Line 19: @@
 To access ROCK Pi S by SSH, try
-   ping debian.local
+   ping ip-of-device
-   ssh rock@debian.local
+   ssh rock@ip-of-device
 or

← Older revision		Revision as of 10:57, 5 July 2019
Line 25:		Line 25:

	ping rockpis.local		ping rockpis.local
−	ssh @rockpis.local	+	ssh rock@rockpis.local

@@ Line 13: / Line 13: @@
    password: rock
-=== Using ssh ===
+=== Using SSH ===
 Package ssh  is pre-installed on ROCK Pi S  system image.

← Older revision		Revision as of 10:53, 5 July 2019
Line 7:		Line 7:

	By default, the ROCK Pi S uses the colorful 26PIN GPIO header PIN19 and PIN21.		By default, the ROCK Pi S uses the colorful 26PIN GPIO header PIN19 and PIN21.
		+
		+	=== Default non-root user ===
		+
		+	user: rock
		+	password: rock
		+
		+	=== Using ssh ===
		+
		+	Package ssh is pre-installed on ROCK Pi S system image.
		+
		+	To access ROCK Pi S by SSH, try
		+
		+	ping debian.local
		+	ssh rock@debian.local
		+
		+	or
		+
		+	ping rockpis.local
		+	ssh @rockpis.local