Stephen at 12:21, 11 November 2022

2022-11-11T12:21:02Z

Zhuhaihao at 08:40, 2 August 2022

2022-08-02T08:40:38Z

Zhuhaihao at 08:38, 2 August 2022

2022-08-02T08:38:05Z

Zhuhaihao at 08:35, 2 August 2022

2022-08-02T08:35:11Z

Show changes

Stephen: Created page with "{{rock3_header}} {{Languages|rock3/dev/usb-device-network}}"

2022-07-24T03:12:04Z

Created page with "{{rock3_header}} {{Languages|rock3/dev/usb-device-network}}"

New page

@@ Line 1: / Line 1: @@
 {{rock3_header}}
 {{Languages|rock3/dev/usb-device-network}}
    [[rock3 | ROCK 3]] > [[rock3/dev | Development Guide]]>[[rock3/dev/usb-device-network | Usb device network]]
 ===Requirements===
@@ Line 13: / Line 14: @@
 * Kernel version
-USB gadget driver must be enabled to configure usb net. You need to update the kernel to at least version 4.4.143-46-rockchip.
+USB gadget driver must be enabled to configure usb net.
 * Stop conflicting services
-So far, Type-C OTG port only supports one Gadget function. To use use USB net, here need to stop rockchip-adbd service.
+So far, Type-C OTG port only supports one Gadget function. To use USB net, need to disable rockchip-adbd service.
 <pre>
@@ Line 27: / Line 28: @@
 ===Load kernel module===
-* Connect the ROCK CM3 IO to PC with a USB  to USB A cable.
+* Connect the Radxa CM3 IO to PC with one microUSB  to Type-A cable.
-* Install kernel module on ROCK CM3 IO
+* Install kernel module on Radxa CM3 IO
 <pre>
-root@radxa-cm3-io:modprobe g_ether
+root@radxa-cm3-io:~# modprobe g_ether
 </pre>
 <pre>
-root@radxa-cm3-io: dmesg -c
+root@radxa-cm3-io:~# dmesg -c
 [   25.792177] using random self ethernet address
 [   25.792239] using random host ethernet address
@@ Line 76: / Line 77: @@
 </pre>
-Test the network, on ROCK Pi S
+Test the network, on Radxa CM3 IO
 <pre>
@@ Line 82: / Line 83: @@
 </pre>
+==== Radxa CM3 IO ---> PC ====
-===Text===
-−
 <pre>
 radxa@x86_64_pc:~$ iperf3 -s
@@ Line 133: / Line 133: @@
 iperf Done.
 </pre>
 <pre>
@@ Line 155: / Line 157: @@
 iperf Done.
 root@radxa-cm3-io:/home/rock# iperf3 -s
@@ Line 193: / Line 193: @@
 </pre>
-===Remind===
+===FAQs===
-−
-If you can't ping the PC or rock pi.You should check your gateway.
-−
-Here's how to check for hardware problems.If it is successful, then the hardware is ok.
-−
-In Rock CM3 IO
-−
-<pre>
-root@radxa-cm3-io:~# route add -net 10.0.1.0/24 gw 10.0.1.1 dev usb0
-root@radxa-cm3-io:~# iperf3 -s
-</pre>
-−
-In PC
-−
-<pre>
-radxa@x86_64_pc:~$ radxa@x86_64_pc:~$ route add -net 10.0.1.0/24 gw 10.0.1.2 dev usb0
-radxa@x86_64_pc:~$ iperf3 -c 10.0.1.1
-</pre>

@@ Line 2: / Line 2: @@
 {{Languages|rock3/dev/usb-device-network}}
-   [[rock3 | ROCK 3]] > [[rock3/dev | Development Guide]]>[[
+   [[rock3 | ROCK 3]] > [[rock3/dev | Development Guide]]>[[rock3/dev/usb-device-network | Usb device network]]
 ===Requirements===

@@ Line 2: / Line 2: @@
 {{Languages|rock3/dev/usb-device-network}}
+  [[rock3 | ROCK 3]] > [[rock3/dev | Development Guide]]>[[
 ===Requirements===

Rock3/dev/usb-device-network - Revision history

Stephen at 12:21, 11 November 2022

Zhuhaihao at 08:40, 2 August 2022

Zhuhaihao at 08:38, 2 August 2022

Zhuhaihao at 08:35, 2 August 2022

Stephen: Created page with "{{rock3_header}} {{Languages|rock3/dev/usb-device-network}}"