Radxa-configuration - Revision history

Stephen at 07:16, 3 March 2022

2022-03-03T07:16:18Z

Stephen at 15:35, 2 March 2022

2022-03-02T15:35:49Z

Stephen at 15:21, 2 March 2022

2022-03-02T15:21:38Z

Stephen: /* Introduction of Radxa Configuration */

2022-03-02T15:10:48Z

‎Introduction of Radxa Configuration

Stephen: Created page with "{{Languages|radxa-configuration}} = Introduction of Radxa Configuration = This document describes Radxa configuration."

2022-02-28T09:03:25Z

Created page with "{{Languages|radxa-configuration}} = Introduction of Radxa Configuration = This document describes Radxa configuration."

New page

{{Languages|radxa-configuration}}

= Introduction of Radxa Configuration =

This document describes Radxa configuration.

← Older revision		Revision as of 07:16, 3 March 2022
Line 6:		Line 6:

	Radxa Ubuntu/Debian: https://github.com/radxa/debos-radxa/releases		Radxa Ubuntu/Debian: https://github.com/radxa/debos-radxa/releases
		+
		+	== Radxa Board Information ==
		+
		+	* Devide Model:
		+	* Serial Number:
		+
		+
		+	== radxa-config ==

	== The Kernel Command Line ==		== The Kernel Command Line ==

← Older revision		Revision as of 15:35, 2 March 2022
Line 26:		Line 26:

	extraargs='''mem=512MB''' max_loop=8		extraargs='''mem=512MB''' max_loop=8
		+
		+	== Configuring Networking ==
		+
		+	=== netplan.io: Network configuration in YAML ===
		+
		+	Here is one example for setting Ethernet and WiFi static IP address on ROCK Pi S.
		+
		+	==== Setting Ethernet Static IP Address ====
		+
		+	Install package netplan.io
		+
		+	root@rockpis:~# apt-get install -y netplan.io
		+
		+	Create file, /etc/netplan/01-ethernet.yaml. If there is no /etc/netplan folder, create it.
		+
		+	root@rockpis:~# touch /etc/netplan/01-ethernet.yaml
		+
		+	Add the following contents to the file, /etc/netplan/01-ethernet.yaml and save it.
		+
		+	<pre>
		+	root@rockpis:~# cat /etc/netplan/01-ethernet.yaml
		+	network:
		+	version: 2
		+	renderer: networkd
		+	ethernets:
		+	eth0:
		+	addresses:
		+	- 192.168.1.200/24
		+	gateway4: 192.168.1.1
		+	nameservers:
		+	addresses:
		+	- "192.168.1.1"
		+	- "8.8.8.8"
		+	</pre>
		+
		+	Run the commands below to apply our changes.
		+
		+	root@rockpis:~# netplan apply
		+
		+	To validate that our changes are applied, run the commands below to view the IP address configuration detals.
		+
		+	root@rockpis:~# ip addr show dev eth0
		+
		+	It should display similar lines like the one below:
		+
		+	<pre>
		+	root@rockpis:~# ip addr show dev eth0
		+	2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UNKNOWN group default qlen 1000
		+	link/ether c2:68:e0:7c:9b:09 brd ff:ff:ff:ff:ff:ff
		+	inet 192.168.1.200/24 brd 192.168.1.255 scope global eth0
		+	valid_lft forever preferred_lft forever
		+	inet6 fe80::c068:e0ff:fe7c:9b09/64 scope link
		+	valid_lft forever preferred_lft forever
		+	</pre>
		+
		+	==== Setting Wi-Fi Static IP Address ====
		+
		+	<pre>
		+	root@rockpis:~# cat /etc/netplan/02-wireless.yaml
		+	network:
		+	version: 2
		+	renderer: networkd
		+	wifis:
		+	wlan0:
		+	dhcp4: no
		+	dhcp6: no
		+	addresses: [192.168.1.220/24]
		+	gateway4: 192.168.1.1
		+	nameservers:
		+	addresses: [192.168.1.1, 8.8.8.8]
		+	access-points:
		+	"rockpi-2.4g":
		+	password: "rockpistar"
		+	</pre>
		+
		+	Run the commands below to apply the changes.
		+
		+	root@rockpis:~# netplan apply
		+
		+	Validate that our changes are applied.
		+
		+	<pre>
		+	root@rockpis:~# ip addr show dev wlan0
		+	3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
		+	link/ether 4a:33:14:54:4a:03 brd ff:ff:ff:ff:ff:ff
		+	inet 192.168.1.220/24 brd 192.168.1.255 scope global wlan0
		+	valid_lft forever preferred_lft forever
		+	</pre>

@@ Line 1: / Line 1: @@
 {{Languages|radxa-configuration}}
-= Introduction of Radxa Configuration =
+= Introduction of Radxa Ubuntu/Debian Configuration =
-This document describes Radxa official Ubuntu/Debian configuration.
+This document describes Radxa Ubuntu/Debian configuration.
 == The Kernel Command Line ==

← Older revision		Revision as of 15:10, 2 March 2022
Line 3:		Line 3:
	= Introduction of Radxa Configuration =		= Introduction of Radxa Configuration =

−	This document describes Radxa configuration.	+	This document describes Radxa official Ubuntu/Debian configuration.
		+
		+	== The Kernel Command Line ==
		+
		+	The Linux Kernel accepts a command line of parameters during boot.
		+	Radxa official Ubuntu/Debian provide one file '''uEnv.txt''' in the boot partition to for user to add the needed kernel parameters.
		+	uEnv.txt is a simple text file that can be edited using any text editor, e.g. nano, vim, etc.
		+
		+	We need to add all the parameters to the line
		+
		+	<pre style="color: red">extraargs=</pre>.
		+
		+	=== Command Line Options ===
		+
		+	==== max_loop: set the number of loop device ====
		+
		+	extraargs='''max_loop=8'''
		+
		+	==== mem: set memory ====
		+
		+	extraargs='''mem=512MB''' max_loop=8