Hipboi: /* Model */

2020-08-25T10:17:01Z

‎Model

Hipboi: Created page with "{{Languages|ROCKPI_13W_PoE_HAT}} NOTOC Home > PoE HAT > ROCK Pi 13W PoE HAT === Introduction === File:Rockpi_e_wi..."

2020-08-25T10:12:38Z

Created page with "{{Languages|ROCKPI_13W_PoE_HAT}} __NOTOC__ Home > PoE HAT > ROCK Pi 13W PoE HAT === Introduction === File:Rockpi_e_wi..."

New page

{{Languages|ROCKPI_13W_PoE_HAT}}
__NOTOC__

[[home | Home]] > [[PoE_HAT |PoE HAT]] > [[ROCKPI_13W_PoE_HAT | ROCK Pi 13W PoE HAT]]

=== Introduction ===

[[File:Rockpi_e_with_13w_poe_angel.jpg | 400px |right]]

ROCK Pi 13W PoE HAT is a HAT accessories designed for ROCK Pi 4, ROCK Pi E, Raspberry Pi 3B+/4, Jetson Nano or ROCK Pi X. The ROCK Pi 13W PoE HAT allows you to power your ROCK Pi 4, Raspberry Pi 3B+/4, Jetson Nano or ROCK Pi X using Power over Ethernet–enabled networks; for this product to be used, the network it is connected to needs to have power-sourcing equipment installed.

It comes with the following features:

* 802.3af up to 13W(5V/2.6A)
* Optional 40PIN GPIO pass-through exported
* Works with ROCK Pi 4, ROCK Pi E, Raspberry Pi 3B+/4, Jetson Nano or ROCK Pi X
* Clean design by hiding the the big transformer inside
* EEPROM for HAT identity and driver probe
* USB 5V voltage output via USB A port(USB OTG function for ROCK Pi E)
* Provide 12V power output with 2P terminal connector

=== Supplied with this product ===
* ROCK Pi 13W PoE HAT
* Mechanical spacers
=== Other hardware needed ===
* One of ROCK Pi 4, ROCK Pi E, Raspberry Pi 3B+/4, Jetson Nano or ROCK Pi X
* An Ethernet cable
* Power-sourcing equipment for a 802.3af or 802.3at Power over Ethernet network

=== Software support ===

The PoE doesn't require software to power and run.

=== Model ===

{| class="wikitable" border="1"
|-
! Model
! Description
|-
| FE
| For ROCK Pi E
|-
| FSL
| FS with 26PIN x2 GPIO pass-through exported
|}

The difference between F3 and F4 is, F3 and F4 uses different GPIO for fan control. F4 use ADC for temperature detection, while F3 uses DS18B20.

=== PINOUT ===

==== PoE HAT for ROCK Pi 4 ====

{| class="wikitable"
! Description || Function || Pin# || || Pin# || Function || Description
|-
| || || 1 || || 2 || ||
|-
| || || 3 || || 4 || ||
|-
| || || 5 || || 6 || ||
|-
| || GPIO2_B3 || 7 || || 8 || ||
|-
| || || 9 || || 10 || ||
|-
| || || 11 || || 12 || ||
|-
| control fan speed || PWM1 || 13 || || 14 || ||
|-
| || GPIO4_C5 || 15 || || 16 || GPIO4_D2 || enable/disable fan motor driver
|-
| || || 17 || || 18 || ||
|-
| || || 19 || || 20 || ||
|-
| || || 21 || || 22 || ||
|-
| || || 23 || || 24 || ||
|-
| || || 25 || || 26 || ADC_IN0 || Get ADC value to get the temperature value
|-
| connect to EEPROM SDA pin || I2C2_SDA || 27 || || 28 || I2C2_SCL || connect to EEPROM SCL pin
|-
| || || 29 || || 30 || ||
|-
| || || 31|| || 32 || ||
|-
| || || 33 || || 34 || ||
|-
| || || 35 || || 36 || ||
|-
| || || 37 || || 38 || ||
|-
| || || 39 || || 40 || ||
|}

=== Dimensions ===
* [https://dl.radxa.com/accessories/poe-hat/rockpi_poe_hat_V1.2_20190521.dwg Download 2D file(.dwg) for ROCK Pi PoE HAT]

@@ Line 38: / Line 38: @@
 ! Model
 ! Description
 |-
 | FE
 | For ROCK Pi E
 |-
-| FSL
+| FEL
-| FS with 26PIN x2 GPIO pass-through exported
+| FE with 40PIN GPIO pass-through exported
 |}
 === PINOUT ===

ROCKPI 13W PoE HAT - Revision history

Hipboi: /* Model */

Hipboi: Created page with "{{Languages|ROCKPI_13W_PoE_HAT}} __NOTOC__ Home > PoE HAT > ROCK Pi 13W PoE HAT === Introduction === File:Rockpi_e_wi..."

Hipboi: Created page with "{{Languages|ROCKPI_13W_PoE_HAT}} NOTOC Home > PoE HAT > ROCK Pi 13W PoE HAT === Introduction === File:Rockpi_e_wi..."