Please enable javascript, or click here to visit my ecommerce web site powered by Shopify.
Jump to: navigation, search

Difference between revisions of "Rockpi4/hardware/revision"

(Change lists)
(v1.2)
 
(One intermediate revision by the same user not shown)
Line 65: Line 65:
  
 
=== Model C+ ===
 
=== Model C+ ===
 +
==== v1.2====
 +
* Initial version
 +
 
==== v1.4====
 
==== v1.4====
 
* Remove M.2 connector
 
* Remove M.2 connector

Latest revision as of 11:36, 5 May 2023

    ROCK Pi 4 >  Hardware >  Hardware Revision

There are three models of ROCK Pi 4, model A, model B and model C. Model A is a stripped down version of model B. Model C is an enhanced version of model B. The differences are:

  • Model A vs. Model B
    • Model A doesn't have wifi/bt model(ap6256)
    • the RJ45 connector on model A doesn't support PoE
    • Model A doesn't have the 4Pin PoE header
  • Model B vs. Model C
    • Model C adds one additional mini DP port based on model B
    • Model C changes the HDMI connector from type A to type D(micro HDMI)

Change lists

Model A | B

V1.3

This is the first MP version, the key features are:

  • User type C for power, adds QC&PD trigger IC
  • LPDDR4 for 1/2/4GB ram
  • Use odroid compatible eMMC socket as storage
  • On board wifi antenna

V1.4

V1.4 is a slightly updates based on the V1.3, solves the issues reported by users. The schematic is the same as V1.3.

  • Changes the USB3 OTG label to simple L/H for Host/Device
  • Add external wifi antenna option, not soldered by default
  • Change the headphone footprint to through hole leg one
  • Change user status LED from red to blue(blinking red led is confusing for some user)
  • A 4MB(32Mbit) SPI flash is pasted by default, for future SPI booting support

V1.5

To fight with the global chips shortage, replace the short of supply chips.

  • ROCK Pi 4A and 4B now share the same PCB(ROCK Pi 4), no wifi/bt module pasted on 4A, RJ45 has no PoE capability on 4A
  • Ethernet phy changed from RTL8211E to RLT8211F(no software change required)
  • Change the headphone detect circuit, use the mic from HP jack by default
  • QC/PD protocol trigger chip changed to CH224D

V1.6(4A+/4B+)

  • 4A+ and 4B+ now share the same PCB(ROCK Pi 4 Plus), no wifi/bt module pasted on 4A+, RJ45 has no PoE capability on 4A+
  • Add USB C input voltage measure from SoC ADC
  • Add EEPROM (BL24C16A) for mac address and serial no.
  • eMMC socket changed to on board chips
  • Three buttons are soldered by default.(1: Maskrom 2: Reset 3: Recovery) See [picture here].

V1.72(4A+/4B+)

To fight with the global chips shortage, replace the short of supply chips.

  • Ethernet phy changed from RTL8211E to RLT8211F(no software change required)
  • QC/PD protocol trigger chip changed to CH224D

V1.73(4A+/4B+)

  • Optimize the headphone jack footprint for manufacturing
  • Board manufactured after 2022-08-05 will have SPI unpopulated. This include future revisions.

Model C

v1.2

  • change to a more tight micro HDMI connector

Model C+

v1.2

  • Initial version

v1.4

  • Remove M.2 connector